Engine and Transmission

6,403 topics in this forum

1. e 7 runs rough when you start it even when warm

   By oilburner, September 4, 2012
   • 21 replies
   • 11.3k views
   • 
   • staxx
   • November 18, 2012

2. TRD-72 ratios?

   By burnin oil, November 12, 2012
   • 15 replies
   • 4.6k views
   • 
   • burnin oil
   • November 16, 2012

3. 2002 eaton fuller semi automatic issues

   By Wilsonic, November 15, 2012
   • 0 replies
   • 1.6k views
   • 
   • Wilsonic
   • November 15, 2012

4. How much torque....

   By JumperAndSon, October 12, 2012
   • 15 replies
   • 5k views
   • 
   • JumperAndSon
   • November 13, 2012

5. Coolant

   By Taxman2580, November 13, 2012
   • 1 reply
   • 1.1k views
   • 
   • Jamied625
   • November 13, 2012

6. Tappet noise under load?

   By Cal8544, October 24, 2012
   • 4 replies
   • 1.8k views
   • 
   • burnin oil
   • November 12, 2012

7. EM6 285 question

   By V8dieselnut, November 8, 2012
   • 6 replies
   • 5.8k views
   • 
   • masterwelder
   • November 11, 2012

8. Reputable Pump shops in northern illinois

   By dds92780, November 6, 2012
   • 4 replies
   • 1.9k views
   • 
   • 4020dt
   • November 10, 2012

9. Mack 673 questions.

   By suprmn, October 9, 2012
   • 10 replies
   • 5.3k views
   • 
   • theakerstwo
   • November 10, 2012

10. T2090

    By One bad dog, November 1, 2012
    • 13 replies
    • 5.5k views
    • 
    • Superdog
    • November 10, 2012

11. shuts down backing up

    By mka, November 10, 2012
    • 0 replies
    • 1k views
    • 
    • mka
    • November 10, 2012

12. engine rebuild

    By meca, October 27, 2012
    • 7 replies
    • 2.2k views
    • 
    • meca
    • November 9, 2012

13. 18 speed repair

    By MACKTRUCKS4, October 9, 2012
    • 7 replies
    • 2.4k views
    • 
    • turckster
    • November 9, 2012

14. rubber drive on injection pump

    By RG40738, November 7, 2012
    • 0 replies
    • 899 views
    • 
    • RG40738
    • November 7, 2012

15. Water pump for thermodyne

    By Tony Ingram, November 1, 2012
    • 6 replies
    • 2.9k views
    • 
    • Dennis
    • November 3, 2012

16. r model clutch plates have "up" stamped on them. which way is up

    By diggin dirt, November 3, 2012
    • 0 replies
    • 897 views
    • 
    • diggin dirt
    • November 3, 2012

17. head bolt torque for ENDT - 675

    By calvin92, October 30, 2012
    • 1 reply
    • 2.3k views
    • 
    • 39 Baby Mack
    • November 2, 2012

18. detroit powered R model

    By fullfuel01, October 29, 2012   

    • vin decoder
    • 19 replies
    • 7.8k views
    • 
    • Superdog
    • October 31, 2012

19. rebuild or replace, 711 with turbo 1 2

    By mackmb212, October 7, 2012
    • 33 replies
    • 6.2k views
    • 
    • theakerstwo
    • October 29, 2012

20. 79 350 starts and idles fine, but dies when revved

    By Mtnmblmech, October 28, 2012   

    • 350 starts idles dies revved
    • 11 replies
    • 2.1k views
    • 
    • theakerstwo
    • October 29, 2012

21. 673 engine oil

    By suejoe6174, October 21, 2012
    • 3 replies
    • 2.7k views
    • 
    • mowerman
    • October 29, 2012

22. Iso head gasket.

    By micahbennett, October 24, 2012
    • 6 replies
    • 1.7k views
    • 
    • 1958 F.W.D.
    • October 28, 2012

23. Trouble code

    By Wilsonic, October 25, 2012
    • 2 replies
    • 35.1k views
    • 
    • Victor520
    • October 26, 2012

24. e-7 #5 cyl. miss no smoke

    By oilburner, October 21, 2012
    • 20 replies
    • 6.4k views
    • 
    • staxx
    • October 25, 2012

25. cracked exhaust manifold 1999 e7

    By dkv411, October 16, 2012
    • 12 replies
    • 5.4k views
    • 
    • staxx
    • October 21, 2012