Maxville Truck

Ok, I'm dumb....lol.. VECU Fuse...Throttle and switch functions are back.... Still didnt fix Tach and Speedo, but thats minor potatoes....To heck with it I'm gonna go burn some gas through the Sidewinder.....

I don't get much of a chance to post on here very often... However I'm extremely proud of what my shop did with this project for me personally... Auction purchase I was going to use for parts, walked out to my yard with a jump pack, hooked her up, wa-la motor started right up... Decided it was worth fixing up... Been a Mack guy since I started with trucks hauling cow manure (MR's basically)... Got into putting farm trucks together, as a few of you know, still pumping and hauling sh*t, besides putting farms trucks together, and sand blasting and painting.. I've been blessed by an excellent group of employees bringing a wide range of skills and capabilities to the table. They don't get near enough recognition for their talents. But here is just a token of that.... recognition... This is not a "perfect build" but nicest truck I personally have.... I'm not a "trucker" in the traditional sense have hardly any miles under my belt, just the occasional "auction purchase I need to pick up"... Remanned Tranny (upgrade from T2180 to T318) I am in need of some minor electrical help... Dash tach and speedo giving grief... lots of diagnosing yesterday, (I think its mostly dash, but not fully convinced yet), but in the process of diagnosing, i tried a different VECU , then went back to the original, now I've lost throttle.... Information about integration between the ISX and the Mack side is elusive at best... looking for anyone that might know if throttle is broadcast via 1939 to the isx from VECU, or if it passed though VECU as throttle voltage to the Cummins computer.... Thanks in advance for any assistance...

I acquired this guy this winter.. Have a notion to shove a 4560 in it , massage the engine with a nice twin turbo setup for my local "parts runner"... truck is heavy spec 65 rears 20 fronts in real nice shape... but has a 15 speed in it now... any thoughts ??

Allison has these........trying to find flywheel housing for 4560 application... mack em9-4560 configuration.pdf E-9 mack 740 config.pdf

Anyone here ever see an E-9 with an allison behind it?

4560? if its got 295 fluid in it and it doesnt look polluted dont change it , maybe change the filters, DO NOT USE AIR TOOLS ON THE FILTER BOLTS HAND TIGHTEN ONLY , you can strip them otherwise..

part number?

I need some expert help, trying to setup stationary PTO operation on a former NYC a Mack LE... total different layout of fuses and relays, than I am used to..(would love a service manual for this build) has lots of extra switches for plow operation...which we are not using, I'm pretty sure its a problem related to parking brake switching into vecu, parking brake light goes out on dash indicator but vcads still sees park brake engaged.. Cruise switch is seen in vcads and set/ resume are both seen...Ive tried all sorts of programming changes trying to simply get some speed control.....any expert insight would be appreciated fyi this truck is going to be mixer cow feed (TMR)

I have an MR with a CEEMAT transmission that we put a fifth wheel plate on, e-7 mechanical engine, needs some love, runs and drives as is, but it is heavy specs, 20 front 44 camelback... has a/c needs a charge ( maybe more)..

Got a superliner I'd sell for a puller... e-9 ambac pump 12 speed tranny.....i think 4.64s might be 4.17 on neway air suspension.....engine runs fine exhaust maniflods need some help and the pump could use a "going though"...

Check the governor , 4 bolt cover on driver side near the output shaft, pull the cover off, grab the governor with the weights in your hand and the gear facing up, squeeze the weights in and out the spool valve inside should move up and down freely if not clean it thoroughly ( look for tiny metal filings) put it back in. try it again, also check operation of your kick down mechanism ( electric, pneumatic or cable) make sure that it functions properly. now for the bad news...... if none of the above helps pull the pan, note how much "gobbledygook " is in the bottum, clean the pickup screen and stuff out of the pan.. "if" there was excessive stuff (metallic, and clutch friction material) be prepared for an overhaul...

try this post....

tryed ebay no luck yet local dealer is checking but nothing yet....

To any of you fine gentleman, I need to purchase an operators handbook for a Mack LE 2000 vintage..... If anyone could help I would appreciate it, new or good used would work...

engine has 2 timing sensors one in the front on passenger side,,, will not start at all if that one is bad, and one under the starter in the flywheel housing, will start but hard if it is bad or has "green wires" bad connection etc....

frozen adjusting ring on a clutch can be freed up using an air hammer........ rattle the cast clutch housing while turning on the adjuster _safety glasses and breathing mask would be suggested...have done it many times ..

about $3000 for an ht740 from ATR in mundelin ILL (866-738-7267), and about $4500 for the hd4560 from the same location.....2 year waranty leaking oil buyer beware could be the tranny came loose from the bell, might be more to it just fyi....

Set it up as a 3 line system.... there is a sleeve that goes in behind the suction fitting, when making the conversion then the "3rd" line is added, then u can put a filter on the 3rd line back to tank... or leave it...

Buyer paid for it.... got here did not like it, I agreed to let him get his money back, so not a faux action.....just a nice guy I guess, you know... keeping customers happy....

Check this out, one of last springs projects....custom cut grill, we have a plasma cutter and can cut virtually any design you want in a grill. Check out our web page www.maxvilletruck.com

Well Superliner is back for sale...... Sorry for the trouble cbooker....Price is going up from here I'm not in a "need to sell situation" so it will be going through the shop as it fits into our schedule, all the small issues will be addressed as we get to them, as everything gets fixed it will add to the price @$95 an hour..... I have a paint and sandblast facility so that will be done also.... at this point as is I have it listed for 12,500 obo. looking for opinions on prefered color.. http://newyork.craigslist.org/jsy/hvo/4929856348.html

Well this one looks OK...... Custom plasma cut Grill and Front Bumper...

I'm pretty flexible with removal times.......as long as its paid for. ill try to get autocar mileage by friday, busy schedule this week....this pic is superliner speedo.

http://spencersales.hibid.com/catalog/54438/march-10th-spencer-sales-downing-wi-online-equip-auction?tab=0 Hey guys and "Gals", I'm having an online auction cleaning some of my traded in inventory out of my yard... If interested check the following link out. I will also answer any questions about what is in the auction to the best of my ability. there is a 1984 superliner in pretty decent shape with an E-9 12 speed, neway air suspension, and small sleeper.

http://spencersales.hibid.com/catalog/54438/march-10th-spencer-sales-downing-wi-online-equip-auction?tab=0 Hey guys and "Gals", I'm having an online auction cleaning some of my traded in inventory out of my yard... If interested check the following link out. I will also answer any questions about what is in the auction to the best of my ability. there is a 1984 superliner in pretty decent shape with an E-9 12 speed, neway air suspension, and small sleeper.