mackcl96

What I would do is install a cross member in the area of the back of the battery box........... Is that frame patched(welded) in the area of the battery box and is there a patch (welded) on the frame behind the cab on the passenger side??? My thought on the fame welding is the tensile strength is weakened from heat and will make the frame act like a rubber band Is that drive shaft made too long and the slip yoke, not working like it should.. Bottomed out? This could be the reason the rear trans seal is puking P.S Your air compressor is puking oil

Mack trucks #10105 Received a speeding ticket in Kansas Received a ticket for bad tires on a 1998 RD Received a ticket for no mud flap reflectors on 2009 GU They have 115 drivers and only 5 trucks...... they need more toys Volvo Trucks North America #335611 Received a ticket for no warning buzzer on a 2012 GU Received an OUT OF SERVICE for an oil leak on a 2012 Volvo Received a ticket for no headlights on a Volvo They have 107 drivers and 87 toys to play with They both have accidents listed,, I never like reading ,,,but it happens http://safer.fmcsa.d...nySnapshot.aspx On a lighter note Paccar owned Kenworth had drugs in it in California

Thanks for the rest of the story,,,,,,,Was a good man and always a Mack nut

With Borg Warner turbos,,,,,,,I call them directly give them the part #s They will give you the flow rate,,Also what the maximum boost it will produce,,And what housings are interchangeable If they are Garret,, I would do the same.

I really need to get out from under my little rock,,,,,,,Did not even know bobby had passed (RIP) The last I spoke with him was 2010 in Litz.

Yes that is them

I remember a few like this around here in the mid 80's was a company truck for a local company called Gilchrist Trucking before that,,, it was called Qweensway or both they are out of Old Forge PA they had F-models with multi green strips too The ones I remember had multi green and no blue but anyway

2012 Alcoa wheel service manual ServiceManual-English.pdf ServiceManual-English.pdf ServiceManual-English.pdf Author mackcl96 Category Modern Mack Truck Info Submitted 02/12/2012 12:31 PM

Step tanks are a pain to polish,,,,,,,unlike smooth tanks just remove the step buff and your done Also when your in muddy conditions the first step is 3 feet long for banging the mud off the second step is 3 feet long so you can take them mud boots off and put your flipflops on to get in the cab Also the longer top step is much more comfortable if you need to piss

My parents had one of these MH's in this color...check for a Georgia bulldog edition tag on the dash There was spread in Owner/operator magazine in 1983 or 84,,with the Georgia bulldog cheerleaders hanging all over it (those days are long gone) Specs were 1984 E9 400 T2090 4.42 level 4 interior (red)

Shit happens again http://www.bigtrucks...ge=survey_sheet

I was worried a little ,,,,,,,you been quiet since you got it Was hoping it wasn't giving you big headaches

Seen G.M. Smith over the years with their signature grill guards (little odd) but were really odd on their MH Macks they had 1987 Mack RW713 Day Cab: VIN #2M2AY40C9HC002635 Mack 500HP 9 Speed LL Trans. with 4 speed aux. Tires 1200 x 24 - 75% 65,000 Lbs rears Truck is in very good condition and ready to work. Price $26,500 http://www.gm-smith.com/index.html

Ok thanks on the F.E.T?,, So that meens,,,,,,,,You are going back to this candy store

Hello ,, Tim You need to get back up there and get the Magnum that sits next to your truck ^^^^^The Magnum looks like the one ,,that was listed a few years ago with that body and listed with a 6 cyl transplant Also ,,,,,Is it a pain with getting them over the border {Title and papers } and do you still have to pay F.E.T??

Morning Gregg Your fine on oil psi.....You have been in that E-Tech to long with 19 psi idle to remember. If I remember 25 psi min hot idle and 90 to 100 full rpm according to Mack .

Yes its a pain dragging timber under the truck with a bottle jack,,,,or if you have a stubby bottle jack put it between the spring and frame

Nortrux has been advertising a TD714 but no picture,,,,Probably because you are haven't shipped it yet

I'm curious what these (proper offsets) you have that are between the rim and drum ,,,,,,,,little concerned on your safety and the people around you ........Could we see pictures

Is it just me .......Your slack adjuster never moved when you came to a stop? My thought on front bounce.....Spring pins and bushing,,Are they tight and no slop up and down

General info Make : MACK Model : TD713 Year : 2012 Type : TRACTEUR OFF ROAD Price : $ S/D Weight : 34,690 LBS Odometer : Engine hours : Inspection SAAQ : Non Statut : STOCK Powertrain Engine : MACK MP10-605C (16L) Transmission : FULLER RTLO20918B Driveline : DANA HD Front axle : MACK 23,000 LBS Suspension avant : RESSORT Steering : Double Rear axle : AXLE-TECH 110,000 LBS Rear suspension : R1000 - HENDRICKSON Spacing : 64" Ratio : 9.59 Frame W/B : 264" C/A : 178" L/P : 303" A/F : 125" Frame: TRIPLE Tires Front tires : 445/65R22.5 Tread : MICHELIN XFE (M) Wheels : ALCOA H/P Rear tires : 385/95R25 Tread : XMH-S (L) Wheels : REMEX Additional equipements Engine brake : MACK POWER LEASH Exhaust : DOUBLE - VERTICAL - SCR FRAME MTG Fuel tank : 2x 142 GAL. ALUMINIUM Interior level : RAWHIDE - BLOOD Air conditioning : Yes, HI-PERFORM Driver seat : AIR - BOSTROM TALLADEGA HI BACK Rider seat : AIR - BOSTROM TALLADEGA http://www.mackstefo...6&IDM=2&IDM2=17

http://www.mackstefoy.com/fr/default.asp?afficherItem=true&Type=0&Item=386&IDM=2&IDM2=17

What the previous owner did with spacers and studs is not correct and MUST be removed. even if it is not causing the shimmy.. Your wheel is not siting on the hub bosses. Stud and hub mount front float rims... use the bosses for stress relief

Year: 1962 Make: Mack Model: B-421 Location: Arlington, TX Type: CLASS 3 (GVW 10001 - 14000) Category: Wrecker Tow Truck Engine Make: Mack Engine Model: en401 Fuel Type: Gas Transmission Make: Mack Rear Axles: 1 TRUCK DESCRIPTION 1962 Mack B-421,This is a beautiful 1962 B Model 42 Mack w/ a 525 Holmes Wrecker .Great trucks for parades, just having fun,or use to market your business.A real attention getter and ready to go.More pitcures email . $10000.00 http://www.commercia...B-421-100442141 1963 MACK C615LST Serial Number: 1143 Stock Number: C-MackBR Hours: U/K Price: $5,500.00 Condition: Good old Truck, Tires 15-20% Description: 4000 Gal Tank, Front/Rear Sprayers w/Hose Reel, Mack V8 Diesel Eng, Would make great Yard Water Truck, Runs Drives and sprays water. http://www.amtractor.../misc/mack.html 2012 MACK GRANITE MHD Straight Truck (Cab and Chassis), Cummins Engine, ISL9 Engine Model, 345 Horsepower NEW "MEDIUM" HEAVY DUTY GRANITES (1) SET-UP AS TANDEM DUMP & (1) SET UP FOR AGGREGATE SPREADER, AIR-RIDE SUSPENSION...CALL FOR DETAILS http://www.truckandt...8&fromResults=1