Jump to content

felicello122

BMT VIP
 View Profile  See their activity

  • Posts

    878

  • Joined

  • Last visited

  • Days Won

    1

 Content Type 

Everything posted by felicello122

  1. felicello122
    Does the 12b program apply to the etech 400 hp motor,2000 year model
  2. felicello122
    I wrap the nuts with electrical tape takes up the slack nicely
  3. felicello122
    I will post a pic Monday when I go to work
  4. felicello122
    Much better
  5. felicello122
    Those wheels always make a difference, looks nice I think I like the day cab look
  6. felicello122
    I am in the Hudson valley, about 2 hours from Cortland, I may be going to the brock way show in Cortland in August maybe I could meet you there yarnall
  7. felicello122
    I have 2, 11.22.5 aluminum stud pilot(ball and seat) wheels.These rims are real close to new, I bought them because I needed the tires that were on them. I Don t really need them, would consider a trade for 2 hub piloted aluminum rims. 11.24.5 size would be fine or 275 for the pair. I will post a pic on monday
  8. felicello122
    The petes and kw with the Cummins are ok, the paccar motors are terrible we run a 2012 titan with the mp10 585 and had its share of troubles, I personally like the old stuff like the 3406e and 3406c and the the older e techs macks and the Cummins screw up turbo and get
  9. felicello122
    Turn the dogs in on the quarter fender flaps, looks good need some hub caps on the axles
  10. felicello122
    Looks good, did you paint the fenders black cause you didn't like the red, looked nice all red too
  11. felicello122
    What's under the hood on that stretched 359 pete
  12. felicello122
    Looks like a super liner bracket and shield on your rd, my rd came with that skinny bracket that is part of the rear cab brace that runs across the frame, very flimsy even with the diagonal bar on it, the muffler is moved forward and the door just clears, your setup looks way nicer
  13. felicello122
    I have one just the green goblins shield, think I posted once for you, I told you 100 I think, let me no if you want it I still have it, 914-474-7383
  14. felicello122
    nice girl in the car, looks like shes not wearing anything on the bottom!!
  15. felicello122
    get a heat temp gun and ck each manifold(ex) hole after you warmed it up on a small drive and see what temps you are getting at each port
  16. felicello122
    That's a lot of power out of that e6, I see big turbo, must be bored a little and big nozzles of course
  17. felicello122
    the hercules a car was just stretched and kw 8 bag airide cutoff installed
  18. felicello122
    Next oil change it should come out, or get stuck on the magnetic plug, if not you can simply stick. A magnet in the drain hole, shouldn't hurt to run it its only going to lay on the pan bottom, as for the dipstick try another dealer or a used truck parts yard
  19. felicello122
    Nice shine on that baby
  20. felicello122
    There is one on the firewall on the left side half way down
  21. felicello122
    Happy belated bday mike
  22. felicello122
    Is this a tractor or dump, im assuming tractor cause they are 38,000 pounders,air ride is great for a tractor and rides way better and wont shake the bounce thr truck apart like the camel, but camel is better for a dump application
  23. felicello122
    Have to be crazy to pay that for a rd
  24. felicello122
    The one in the dash is responsible for accessories,like lights and heater, etc, not very expensive wouldn't hurt to replace, sounds like it is bad, they usually make a click sound when you first turn on the key
  25. felicello122
    Could simply be just your dimmer /turn switch

BigMackTrucks.com

BigMackTrucks.com is a support forum for antique, classic and modern Mack Trucks! The forum is owned and maintained by Watt's Truck Center, Inc. an independent, full service Mack dealer. The forums are not affiliated with Mack Trucks, Inc.

Our Vendors and Advertisers

Thank you for your support!

Mack Related Links

Popular links

BMT Forum Logo

HTML tutorial
×
×
  • Create New...