blackdog2
-
Posts
1,459 -
Joined
-
Last visited
-
Days Won
14
Content Type
Profiles
Forums
Gallery
Events
Blogs
BMT Wiki
Collections
Store
Everything posted by blackdog2
-
Change oil pump and bearing's........they had a problem with Jake's not working some dealer's were putting in oversized bearing to increase oil pressure and external oil line's for feed ?
-
94 CH613 E7 Electronic & Engine Shutdown Lights
blackdog2 replied to msbulldog601's question in Mack Truck Q & A
Have same problem radiator low water sensor is to high drops low it goes of ? 1993 CH-613 -
What was the spec's year ?
-
All his stuff is way OVER-PRICED 100%....
-
$6.499 in Connecticut this minute might change ?
-
Look up " Gas Buddy " tell you were the cheapest gas or diesel anywhere ?
-
THANK'S FOR THE Wish's....
-
A few year's...............OLDER ?
-
I'm running Cooper's on my Mack tri-axle's 4-year's now haven't a problem all the way around but they won't fit on anything being so wide coming so close to spring saddle or fifth wheel mounting....
-
RM-852 Cooper's 11-r x 24.5 just paid 2129.51 for 4 price's going up 466.00 a piece.....
-
We have a tractor with 80,000 rear's it has 14.00 X 24 tire's dry rotted often wonder the cost to replace ?
-
I've been paying for 425/65-22.5 rm-332 .....721.15 out the door front float's Cooper's tax included and no old tire fee ?
-
They just got rid of everybody Sonny daughter's and the good Guy's the 1-guy was in the commercial shop he went on his own and Work's for O & G every mornin then has other account's to fill out the day my son ran in to him a couple of week's a go.......Sonny' son-in law ran it into the ground and owed Million's to the bank ......the price's went out of site I bought a lot of tire's for year's from Sonny open 6:00 am
-
Can't get them in Conn. .....I finally pic one up at Toce tire 3-day wait
-
I have a 350-HP 2001 RD when new had the same the dealer were putting " oversized " bearing to increase oil pressure ......then corporate say's we have a fix a new oil pump so mine was the fix before the external line's in other area's work well after ?
-
I have gotten a few law's change salt on the permit and using permit from exit 42 down to exit 18 Westport from 73,000-to 76,500 now the DMV sit's there waiting everyday also the power unit has the overweight permit and can pull any trailer I was stop in Norfork on a Sunday 7:00am was issued a 1800.00 ticket wrong trailer on permit........went to court in Bantom did a little arguing and was thrown out......
-
Well in the back wood's are a little behind time's here in Connecticut they look for a " Chassis Modification Decal " you can have a tri-axle but no decal you get a ticket for a ten wheeler a buddy of mine got a ticket for exceeding tire rating ........he was 138,000 plus other ticket's on a trailer dump off loading a salt ship the fine was over 40-K ?
-
No......I work for a rigging comp hauling pre-cast tore them apart it's not safe State Police / DMV are looking for underrated suspension's / tire's .....We had 26 + tractor's on a daily basis 200 mile radius....
-
I have 1...
-
they always sell that type of equipment broken frame's , trunion's basket job for BIG Money ...
-
Have a 1984 galvanized been sitting no rust ?
-
Not in my front yard ?
-
11:00R 24, Tire Wobble
blackdog2 replied to Red Horse's topic in Antique and Classic Mack Trucks General Discussion
Hallamore motor trans. doing I-691 for blakeslee for Arute bro's we had 2 DM-800 and 2DM-600 96-beam's for all bridge's crossing with 5-axle trailer's 90-ft long on a bolster plate with a 3/4 cable in between . -
11:00R 24, Tire Wobble
blackdog2 replied to Red Horse's topic in Antique and Classic Mack Trucks General Discussion
Webb wheel's very good hub's -
11:00R 24, Tire Wobble
blackdog2 replied to Red Horse's topic in Antique and Classic Mack Trucks General Discussion
I've change 4-tire's on a Mack DM-600 with a 62-ton concrete I-Beam on I-691 by hand early 80's no help and they wonder why I left ?
BMT Forum Logo
