Jump to content

IH Farms 2

Bulldog
 View Profile  See their activity

  • Posts

    262

  • Joined

  • Last visited

 Content Type 

Everything posted by IH Farms 2

  1. IH Farms 2
    Mine is direct mounted with an extra bracket hasn't been an issue. Only been on for a couple months though
  2. IH Farms 2
    Mine would do that when the belts are loose or the alternator is getting ready to puke.
  3. IH Farms 2
    You can see what I did in this picture
  4. IH Farms 2
    I welded the ends but not the flange part plus bolted every thing
  5. IH Farms 2
    Superliner frame to newer CH frame unknown year about 3 ft of double frame works great no issues after 3 yrs
  6. IH Farms 2
    I'm gonna play with the wires tomorrow see what happens
  7. IH Farms 2
    88 had a mechanical speedometer to being with I converted it to electronic 3 years ago. I do not know what year the trans came from other than newer
  8. IH Farms 2
    Yep I just need to get the sender to produce a signal with the proper wires connected
  9. IH Farms 2
    I have a gps but seeing as the cop that did a level 1 inspection on me asked if it worked last year thinking it should work. Plus I like tracking miles for mpg and miles in different states ect since I have apportioned plates on it
  10. IH Farms 2
    This one is pretty easy to calibrate hold the trip reset turn key on guage goes into calibration mode. Use a predetermined 2miles press the reset again drive the 2 miles then hit it again at the end
  11. IH Farms 2
    Ok I'll try that. The signal generator I had on the cable drive was a 3 wire so it had power, ground and signal
  12. IH Farms 2
    Can anyone tell me how the 2 wire sensors should be wired? One is a signal wire I assume should the other one be grounded or powered? I had to change the trans in my superliner before Thanksgiving and the used trans i found has a speed sensor would like to get my speedometer working again. Have an autometer electronic guage installed already
  13. IH Farms 2
    BLP trucking R piling corn.
  14. IH Farms 2
    I have a neway cutoff with mack axles 3.87 gears.
  15. IH Farms 2
    No wonder I didn't see you on 20 last week. Enjoy retirement
  16. IH Farms 2
    Delco 22si is what is on my 88 superliner
  17. IH Farms 2
    When I went to buy one a few years ago it was piece work. But they may have been out of the complete reman stuff I don't know
  18. IH Farms 2
    I'm looking for a good used door for my superliner. Prefer with the window and guts but empty shell is fine
  19. IH Farms 2
    Bunk is sold
  20. IH Farms 2
    I live in dekalb county so don't have that problem. I know with cars it's like 96 and newer these days.
  21. IH Farms 2
    It's not too different looking
  22. IH Farms 2
    Hampshire Illinois
  23. IH Farms 2
    36" bunk from superliner good condition no rails included single cut out for exhaust has blower motor and heater core works good 400 obo
  24. IH Farms 2
    I have a cut off from an 88 superliner 34k neway mack axles 3.87 ratio want 1200 obo will trade for unimount hubs can load frame rails are no good that are attached
  25. IH Farms 2
    I have a neway air ride off of an 88 superliner with 3.87 gears. Came off of a running and driving truck frame rails are junk

BigMackTrucks.com

BigMackTrucks.com is a support forum for antique, classic and modern Mack Trucks! The forum is owned and maintained by Watt's Truck Center, Inc. an independent, full service Mack dealer. The forums are not affiliated with Mack Trucks, Inc.

Our Vendors and Advertisers

Thank you for your support!

Mack Related Links

Popular links

BMT Forum Logo

HTML tutorial
×
×
  • Create New...