Full Floater

That's the stuff. Now is the protocol to update the lead wire...if it hasn't already been done, to a new style?

Sure seems as if a lot of parts interchange between the E6....not sure exactly what's what with that.

Yes, the manual that I have, shows and describes this process. I hadn't seen it before and it scared me haha. It also shows a lip style seal and states there are a few different options. I try to acquire the parts I need prior to tearing into something but maybe I should tear into this and find out exactly what is in there. OR just leave it alone

Does anyone have any insight as to what crank main seals I should order? In particular, the rear? And is there a special service tool needed to install the seal on these? I have done many a crank seal, but never on a Mack 675....so just want to make sure this guy goes in right.

Thank you for sharing that pic of your lifting apparatus. I like it. I am going to try my best to avoid using the head bolts. I'll see what I can come up with

Awesome, thank you.

I'm about to lift 2 different 675, 235hp engines to swap one of them into the other truck. I have never lifted a Mack engine before and I plan on using a steel cable/strap under the rear of the bellhousing/clutch housing; but still need an idea for lifting the front. I have read that some have used the valve cover bolts to affix a bracket to (I'm not that brave). And some have used a couple head bolts. I am really not wanting to disturb the head bolts on the one good running engine that's being pulled. Are there any other ideas on a front lifting point? Thanks

Is there a particular temp that these engines "like" to run at? It's cooling system re-fresh time for me on a Canadian 235 and I want to do the thermostat while im in there. It's in a tow truck that doesn't tow max gvw loads and short trips more then long trips so im thinking a 170 or 180 degree stat

No updates on my end. I have several engines that could use this. I just simply haven't looked any further into it

Yes, I think re-sealing as much as possible is the ticket. Front and rear mains, timing cover manifold gaskets? oil pain. Not the head gaskets. does the oil cooler have any seals? It runs and starts great, no blow by, no leaks, no oil in air tanks that I tell. about 8000hrs on it. 320,000miles or so. It hasn't been worked as hard as some. I could just throw it in as is, but i'd like to do a little better then that. Freshen it up a bit, and bump up the reliability factor. This is a project for ME to use, not doing this on a customers truck. It's being made into a single axle rollback truck and will work daily. With me driving it, no cowboys.

Are there any leak prone seals or anything that would be easier addressed while the engine is out? It's going into a Western Mack, so narrower frame rails make a few areas like around the compressor and power steering pump, difficult to access.

Will be swapping a good running ENDT 675 235hp from a truck with a bad body, into another chassis that's already equipped with a 235, but is worn out. Both are 107 6 speed trucks. The donor engine runs like a top, but I would like to re-seal or service anything that should get done when the engine is out of the truck. Rear main, oil pan etc. Im new to swapping these engines, can anyone give me a quick "list" of things I should look at while the engine is out and easily serviced? It will be getting a new clutch while it's out, jacobs 675 jake heads (overhead adj obviously) and fresh injectors, hoses etc.

This axle is from a 1976 R 685ST Yes I will be pulling the hubs to give it a good inspection and replace the hub seals for sure and likely the brake linings. Hopefully I can get a number off the seals when I pull them out. Will change the gear oil and probably leave the rest alone for now. Yes I do believe that the "power divider" description in the build sheet might be reference to a LSD type axle, shifting power from side to side instead of axle to axle. After checking oil levels I will drive the truck over some loose ground with no weight in the back and see if both wheels have a tendency to put power to the ground instead of just one wheel. I think painting the MACK lettering on the rear of the axle in the same red that the cab is going to be, is and excellent idea. Let everyone behind me know for sure they are following a pedigree Mack. May as well throw some Mack "greatest name in trucks" mud flaps on to!

If anyone out there has a service manual for this particular axle, and is willing to sell it.....I'd buy it

I'm totally unsure at this point. Have not pulled the hubs off this one, yet.

Anyone know the oil grade they require? I would guess probably 80w-90 but i'd like to go 75w-140, just wanna make sure I don't bugger this thing up by doing that

They can sure bring a man to almost tears. I have a White Western star that is almost as bad. Also swapped that to a 39MT on the Big Cam Cum-a-part which made install easier

Thank you. Yup im hoping it will turn out well. It's a 23k rating which is exactly what I need for the application it's going into. And im just fine with spring suspension. It's fairly low mileage and feels tight

Finally getting around to uploading a pic. This is the 39MT in a Western (narrow frame) 1975. Don't mind the mess, the truck's being resurrected from the dead

Ya im not into the additional stresses on the engine, BUT......I would be interested to see if a compound turbo setup could be tuned to drastically reduce that thick Mack exhaust smoke on upshifting/acceleration

Yeah they are rare here to. Everyone tells me to put an Eaton and air susp in this truck im building but I would MUCH rather run this Mack single drive rear just cause it's something different. And being Mack, probably better. Im hoping.

Hi. Im working on a single axle R with a RAD529C and a CRD1171 Carrier. Do we like these axles? Is there anything to look out for in regards to problems? According to the build sheet and some info I found online, the CRD1171 is some sort of power divider. How does that work in a single axle? Thanks

If anyone has a fiberglass Lund style visor and willing to ship to BC canada, please let me know.

Thank you for the detailed response. Would YOU go thru a conversion from pos to neg ground, if you were in my shoes?