Jump to content

Moparmike

Bulldog
 View Profile  See their activity

  • Posts

    274

  • Joined

  • Last visited

 Content Type 

Everything posted by Moparmike

  1. Moparmike
    No I didn't but will get right on it cause the truck is doing a great job since the inframe..time to go back in for a overhead check I'm on about 3 4 thousand miles now no smoke great power comfortable truck just working on the little stuff now ..thanks guys
  2. Moparmike
    Never thought about switch ..it goes days no problem then shut down and fires right back up no issues after that ..but will look into that
  3. Moparmike
    Ok I replaced the relay and didn't have a problem for a little while but it shuts down every now and then..I check the railway when it shut down and its warm not hot just different from the other 3 so I'm thinking of putting in a 100amp relay and replacing the 70amp or even just putting the solenoid like other models have ..what's your thoughts..thanks guys
  4. Moparmike
    I have 3 ed mack 2 2000 and 1 2001 why do everyone of these trucks frame crack at the back by the rear end running the long way ..dot told me park it dont lif it back on the road its dangerous smh
  5. Moparmike
    Yes so a replacement is the only fix I guess dang lol truck killing me
  6. Moparmike
    2001 rd 688s tech and speed works great but nothing else works no mph trip or hour meter is there away to check repair this ..really need mileage if possible..thanks for the help
  7. Moparmike
    I hope so I changed the 3rd relay it had a black burn spot on it..put electric grease on all them .ran 11hrs yesterday no problem so far working it today so far its good.. Thanks for all you guys help
  8. Moparmike
    The 4 relays are the only thing I've found in here with big hot wires that run back out the truck
  9. Moparmike
    Took passengers side dash off looked everywhere cant find this relay mack said chrome like a ford cant find it ..1 on driver side firewall but they said that's not it..anybody have a picture just for reference that may help me thanks
  10. Moparmike
    The 4 power relays are they the relays in need to be looking at
  11. Moparmike
    Yes blower motor stops when it shuts down..where can I find this relay at 2001 rd 688s E7 Thank you guys for your response
  12. Moparmike
    Install a new sensor on front of engine and in ball housing..would that stop the heater and cruiser from working if so I'll replace them again could have got a bad set
  13. Moparmike
    Also cruise control is not working now was working..I cant idle the truck up once air pressure builds but could before
  14. Moparmike
    2001 rd just did inframe less then 1000 miles on it..someone replaced the original engine with a 99 e7 427 same engine from factory just different year put new vecm had mack reprogram it to specs truck runs fine then will shut down red x comes on heater blower everything shuts down wait a few minutes starts right back up run 15 min or less shut down no codes what so ever..please help I'm so deep in this truck and not able to run it ..first did it last week ran bout 12hrs no problem then started this Thanks in advance
  15. Moparmike
    Anybody know if I can delete codes are the codes are from my truck
  16. Moparmike
    Ok guys put the vecm my buddy has in truck runs great .does the vecm store codes from the previous truck..soon as I started the truck it has 3 codes 1/3 5/5 7/ 2 ..the lighting volt seems to stay on ..can I have the codes cleared and hopefully the light goes out ..drove it about 80 miles home no problem..thank In advance
  17. Moparmike
    Friend has a vecu but the last number is a 3 instead of 5 will that make a big difference..its a 1999 EU 427 vecu out a ch I think he said
  18. Moparmike
    Yes 2001 rd the computer I need is on the passenger side dash bolted to a cover
  19. Moparmike
    Mackpro I've found a company that has a ecm same numbers same engine would I still need a reflash or it would be hit or miss..also what's the average cost of a reflash on the ecm.. Also hi tech in Texas said they would repair what's wrong on my ecm and send it back its 750.00 Thanks for all the help. I've had this truck 6 mths been in the shop all 6 except for 1 week new inframe and clutch now 30 miles down the road ecm goes out ..
  20. Moparmike
    Are a repair if possible
  21. Moparmike
    2001 ed e7 what numbers are needed off the computer I have to get
  22. Moparmike
    Ok guys update on what I've found.. Took cover off passenger side with computer on it shock white plug light went off truck runs fine..o took computer out cleaned it up put electrical grease on pins reinstalled plugs truck has been running great..thank you all for your help..
  23. Moparmike
    Can someone tell me where all the truck grounds are on a 2000 rd I'd like to check those as well
  24. Moparmike
    Turn in a driveway this morning and hit a bump truck just lost all power only idle to 900 code 6 4 had that happen before took batteries lose no more problems..today nothing still no power I took the gray triangle shape plug apart with the green yellow and black wire pull ecm fuse let truck sit no battery hooked up even took the plugs off the computer on the passenger side of motor nothing..just went out on job ..first day and 1 hr on new job..Smh ..anybody got any ideas to try right here at Christmas is not a good time to be out of work..or even get run off the job..any help is appreciated thank you
  25. Moparmike
    I see there are a few oil plugs on the rear end are they all connected as in does the top 1 feed the bottom are do I need to check and fill each ..didn't want to pull the bottom and fluid goes everywhere..

BigMackTrucks.com

BigMackTrucks.com is a support forum for antique, classic and modern Mack Trucks! The forum is owned and maintained by Watt's Truck Center, Inc. an independent, full service Mack dealer. The forums are not affiliated with Mack Trucks, Inc.

Our Vendors and Advertisers

Thank you for your support!

Mack Related Links

Popular links

BMT Forum Logo

HTML tutorial
×
×
  • Create New...