Jump to content

Joey Mack

BMT Benefactor
 View Profile  See their activity

  • Posts

    9,116

  • Joined

  • Last visited

  • Days Won

    213

 Content Type 

Everything posted by Joey Mack

  1. Joey Mack
    That was my question this whole time... How could they figure out 500+ names on Jan. 6 but cant tell who brought cocain into the white house.. BullSh!t !!
  2. Joey Mack
    PTO's are always turning when the truck is running.. When You shift the PTO into gear is when it goes to work..
  3. Joey Mack
    $3.59 + here in Salisbury.. (Gas),,, Diesel $4.09 ish.
  4. Joey Mack
    Ok.. rear mount uses the bottom counter shaft. I believe side mount does too. Therefore the same countershaft is turning, but PTO position is different
  5. Joey Mack
    Bob. All of the countershafts are turning at the same time, only when you select a gear and a range does the output shaft turn.. Happy Monday Bob...
  6. Joey Mack
    Mech I think you were able to spread dump as well as stationary. It was all in how you picked the gears and range. Or neutral if needed..
  7. Joey Mack
    The trucks I drove had X-107's..
  8. Joey Mack
    If they are the same as an END 673. I may have some..
  9. Joey Mack
    Mike1, that post is 5 years old. Check the engine grounds in front of the starter, and also, unplug the Duetch connector at the injection pump, and inspect for loose pins and cracked wires... You could, wiggle that plug while it's running to see if it cuts out and in, before you unplug it.. it should be secured in a yoke
  10. Joey Mack
    I believe you put the aux. Box in neutral, then you can select 1st-3rd depending on the PTO speed you need. It's been over 20nyears since I drove a 2 stick R/DM model dump truck.
  11. Joey Mack
    Hell, I have too many trucks as it is.. Thanks anyway..
  12. Joey Mack
    Yep, grinders
  13. Joey Mack
    🍻
  14. Joey Mack
    I'm curious, but it's really none of my business.... What is that Blue Oval worth??? I'm at $4,000.00 But really don't know.. It looks like a good truck to have for going to the hardware giants and the scrap yard, and the landscaping yards to get stone or mulch, etc:... anyway.. someone is gonna get a good work truck.. Jojo
  15. Joey Mack
    ''Submarine Sandwich'' When I was kid on Lawng Guyland....
  16. Joey Mack
    Hell Tom,, I'm gonna Miss it for you..
  17. Joey Mack
    Well,,,,,,,,,, I might be?? and Damn Proud of it !!! I hope this weekend has been good to you guy's... Jojo
  18. Joey Mack
    I guess I have a #1..
  19. Joey Mack
    here is mine..
  20. Joey Mack
    Yes sir, prices are out of sight.. I just bought a 12'x20' carport.. $2,100.00 installed,, 13 years ago I bought a 12'x16' for $600.00 installed.... 7 years ago I bought the big gas powered V-Twin air compressor that Harbor Freight sell's, for $1,100.00.......... I was in there a few days ago. They had a ''Closeout sale Price tag on it'' $1,999.00 I will admit,,, I am very happy with it and it really does make 180 PSI.. It runs my new blasting cabinet quite well.. at the steady 80 PSI required by the cabinet.. Jojo
  21. Joey Mack
    I just looked through all 60 pages of the book.. It's like you,,, A wealth of info.. thanks again.. Jojo
  22. Joey Mack
    Thanks GW.. I saved that info to the folder I have for my KB.. I hope to get started back on it this fall.. I have other obligations.. Jojo
  23. Joey Mack
    it doesnt look all that bad.. pressure test the CAC.. Cracks appear at the top right corner and run down the weld where the viens meet the side tanks.. usually on the front side.....
  24. Joey Mack
    the camshaft number is the real deal when figuring engine brake lash..
  25. Joey Mack
    here are some pics from my E-7 book..

BigMackTrucks.com

BigMackTrucks.com is a support forum for antique, classic and modern Mack Trucks! The forum is owned and maintained by Watt's Truck Center, Inc. an independent, full service Mack dealer. The forums are not affiliated with Mack Trucks, Inc.

Our Vendors and Advertisers

Thank you for your support!

Mack Related Links

Popular links

BMT Forum Logo

HTML tutorial
×
×
  • Create New...