Jump to content

Joey Mack

BMT Benefactor
 View Profile  See their activity

  • Posts

    9,141

  • Joined

  • Last visited

  • Days Won

    214

 Content Type 

Everything posted by Joey Mack

  1. Joey Mack
    Auto to stick...
  2. Joey Mack
    well, at least with the 13 spd. you can get up to about 60+ MPH.. Is it a dump truck or roll off, ?? tractor??
  3. Joey Mack
    Sorry Bud... Thats all I got... if the engine would run above 1400,on up to gov. speed I would say install starter button until you find the issue.. I had a deleted MP-7 that gave trouble in many ways, and the ignition didnt start the truck. I put a starter button in it and it worked fine. It was a homemade dump truck that a crop farmer had.. his was a manual trans. though.. I wish I could help.. Jojo
  4. Joey Mack
    Pull fuse 71 out of the EPDM and see what happens.. that is the Allison fuse.. can you jump the little relay on the starter to turn it over?
  5. Joey Mack
    that is a great find.. thanks for sharing it.. jojo
  6. Joey Mack

    Happy Birthday !!!   

    1. terry

      terry

      👍 :MackLogo:

  7. Joey Mack
    if you unplug it,,, what happens?? also, have you checked the wires going into the cab for cracks and chaffing?
  8. Joey Mack
    Do the headlight wires run behind the oil filters? If so, check there, especially at the wire clamps bolted to the engine.
  9. Joey Mack
    It makes for a smooth rotation in the joint. If ujoints are straight on,, the bearings won't rotate, and that will cause Brinelling...
  10. Joey Mack
    I always suggest checking the Duetch plug at the injection pump. Those pins can come loose in side.. also check for bad wires on the truck side of the harness..
  11. Joey Mack
    when you get it apart you can bench test it. look closely at the sliding clutch and clutching teeth on the outer cam drum also.. you dont need to use high air pressure to actuate the shift fork and clutch, it can fly out..
  12. Joey Mack
    can you rotate the yoke back and forth to dissengage the 'peanuts' in the power divider?
  13. Joey Mack
    you should be able to leave the power divider drum in place, and pull the shifter section out by itself.. what makes you think it needs inspecting??
  14. Joey Mack
    The metal plate they are part of comes right out of the rubber bolster.. I have seen that dozens of times..
  15. Joey Mack
    box rubbers!! Atro makes a decent affordable kit, with the bolts.. You may want to get 12 more washers.. if you like washers on both sides of the bolt.. and put twinkies in the boxes too... jojo
  16. Joey Mack
    have you looked at the torque arm bushings, and the box rubbers, as well as any wear on the spring tips in the boxes? they should not touch the boxes anywhere.. if the upper pads are worn out badly, you will be able to wiggle them without jacking the truck up.. and of course there is always the trunnion bushings too.. but lets keep it basic..
  17. Joey Mack
    Here is a tool I made about 10 years or so, ago.. I needed to diagnose tire wear on a truck that was in a minor wreck. I made this tool to measure the distance between the drive axles to see how far off they were.. Its ugly, but it works and I will still use it today if needed.. I basically made 2 sliding pointers with clamp bolts, and slipped them over some wire conduit.. i sharpened the tips of the pointers so they would fit good into the dimples on the axle flanges..
  18. Joey Mack
    Camel back or Hendrickson HN or Walking beam rear suspension??
  19. Joey Mack
    Ok,, I have this book. Here is what I think you are asking for.. Text me if you cant read it clearly or for whatever reason. 704-785-1738
  20. Joey Mack
    Too add to the idea of removing the cam gear on the engine.. When the time comes to put it back on, you have to bake the gear in an oven to around 450-475 degrees, then quickly install it and 'seat-it' on the cam (cam standing up with thrust washer in place).. there will be know way to hold the cam and keep it from pushing into the block and the trust washer will fall and get between the gear and cam, also take the chance of pushing a cam lobe into a lifter roller. Yours is a 2002.. It may have ceramic roller lifters.. The lifter roller WILL crack.....
  21. Joey Mack
    3 degrees.. You may be able to find a shim plate for the center bearing mount that will be a 3 degree shim. I will be in my shop in a couple hours. I will look in my drive shaft book for info. Jojo
  22. Joey Mack

    Happy Birthday  !!!  

  23. Joey Mack

    Shop Talk

    Joey Mack replied to Onyx610's topic in Odds and Ends

    Yes I have.. !! Matt is doing great !!
  24. Joey Mack

    Shop Talk

    Joey Mack replied to Onyx610's topic in Odds and Ends

    I aint a Blue Oval Guy... But....... A Kickass car or truck... is a Kickass car or truck.!
  25. Joey Mack
    Christ Almighty !!!!!!

BigMackTrucks.com

BigMackTrucks.com is a support forum for antique, classic and modern Mack Trucks! The forum is owned and maintained by Watt's Truck Center, Inc. an independent, full service Mack dealer. The forums are not affiliated with Mack Trucks, Inc.

Our Vendors and Advertisers

Thank you for your support!

Mack Related Links

Popular links

BMT Forum Logo

HTML tutorial
×
×
  • Create New...