Jump to content

Joey Mack

BMT Benefactor
 View Profile  See their activity

  • Posts

    8,964

  • Joined

  • Last visited

  • Days Won

    209

 Content Type 

Everything posted by Joey Mack

  1. Joey Mack
    have you taken the belts off and run it?
  2. Joey Mack
    do you have an infrared temp gun? if so, when it gets hot, pull over raise the idle up and check the water manifold at the rear of the rear manifold, and see if it is close to what the gauge says. there may be 10-15 degree difference due to shooting the outside of the manifold and not the coolant. just curious if you have a gauge issue or sensor issue right now. BTW... your truck is a CV-713 not 513.. Jojo
  3. Joey Mack
    are you hearing the air compressor kick on and off?
  4. Joey Mack
    typically 50 PSI of freon is enough to start the compressor, one of my issues was not being able to jump start or test the compressor with the engine off. it is a 3 wire harness, unlike the 2 wire harness we know.. wont hurt my feelings if I never learn how to fix this disposable compressor.
  5. Joey Mack
    I respect that.. I was a builder at Mack for years and the price of re-man w/warranty out weighed an in-house rebuild.. too bad.. I took pride in my builds..
  6. Joey Mack
    I am not able to answer most of your tech. questions, GW.. but what I do know, is it makes trouble shooting A/C issues harder, especially on a road call, and you dont have a laptop with the correct programming. Even with A-Pads on the truck I have struggled with them. I dont like to just throw a compressor on as a guess, I want to know why, before I spend the customers money..
  7. Joey Mack
    here is a sample. it is controlled by the EECM.
  8. Joey Mack
    Of course i have..
  9. Joey Mack
    It is impossible to do it 'in-chassis' without several special tools.. if you pull the trans out and stand it up on the bell housing, using some 2x8's, you can do it.. i highly recommend getting the book, this aint no parts changing job
  10. Joey Mack
    That is a check ball in the tank vent, lets pressure out, and keeps dirt from getting in... Theoretically
  11. Joey Mack
    Actually, there is a clutch, it just isn exposed. It is behind the pulley.. i dont care for them. Im with you G W.
  12. Joey Mack
    Isnt the clutch on that model internal? If its the Sanden that i have seen before, you wont see the clutch engage. G.W. makes some good points though.. was the expansion valve replaced recently.
  13. Joey Mack
    Dammit!! Busted again...
  14. Joey Mack
    I had a thought... (Uh-Oh) . Carburetors are aluminum...
  15. Joey Mack
    too bad we are so far apart. I have access to lots of cut offs.. both stainless and #2 steel and aluminum too.. I get it for free.
  16. Joey Mack
    That is pretty nice. Thank you for thinking of me.. My plan for the truck was to be a toy.. I was thinking about putting a 5th wheel on it for looks, and a short rack body behind the cab for groceries ( I do have 13' of frame behind the cab) I didnt think about a hitch. however, if i'm in a parade, I could pull a hay wagon full of kids and their parents. Hmmm...
  17. Joey Mack
    Boost leak? Is the EGR valve still on the engine?
  18. Joey Mack
    man that truck is sweet !!
  19. Joey Mack
    I just learned something.. never knew about gas and aluminum tanks..
  20. Joey Mack
    sounds like you need to put gas tank coating in it while it is a virgin... sorry, I dont have a picture of a girl in a car.. But I do have this little Peach.. as Bob would put it.. jojo
  21. Joey Mack
    whats with the flipping of the shifting hand by both of them? Learn me something...
  22. Joey Mack
    Back in 2001 or 2.... Hanaford bros. Grocers traded in 32 CH 612's and 613's and bought 36 CX's.. ( new model that year). The trade trucks ranged from drivable and workable, to wont move or run. We picked out the runners and piggy backed the bad ones, on them. The buyer was from Guatemala and was the only one who spoke english. I even had to show a couple of them how to release the brakes and shift, on the lot.. They can drive anything there, much like Laredo TX.. saw that in 2006...
  23. Joey Mack
    Yes, i bet we have better trailers sittin in scrap yards.
  24. Joey Mack
    Looked like a late 90's CH.. that truck aint seen no treatment, just abuse.. its a funny video. Looks like fun too.
  25. Joey Mack
    I watched it again with my wife.. First thing she says is.... Well, thats how I drive... My left foot stays on the floor... Dahh... Also noticed the red button isnt pushed in, so i guess hes not pulling a trailer, unless the trailer looks like the truck, and doesnt have maxis, or brakes for that matter..

BigMackTrucks.com

BigMackTrucks.com is a support forum for antique, classic and modern Mack Trucks! The forum is owned and maintained by Watt's Truck Center, Inc. an independent, full service Mack dealer. The forums are not affiliated with Mack Trucks, Inc.

Our Vendors and Advertisers

Thank you for your support!

Mack Related Links

Popular links

BMT Forum Logo

HTML tutorial
×
×
  • Create New...