Joey Mack

Thats not what he posted. I dont have any other vin' s right now. May be a CHU grill is what he posted.

there may be a scetch of what the grill looks like when they bring the picture up. these 2 trucks fall in the 2004-2006 range. same bolt pattern.

Try: CHN-613/003358 -or- CHN-613/003821

YEP!!

If that was a valve the engine would be running terribly.. i second the idea of a left behind peice of metal

JoeH is right. Also, un plug the dash light dimmer switch and try it again. Those switches can cause issues.

I assume you found the #'s ?

The part number is cast into it on the back.

Isnt the 07' an MP-7?

in my note book, pin #8 on the left terminal strip on the firewall, is the headlight power, but for some reason I didnt write down which was high beam. I'm also missing a note book from an RW that I re-wired... It had better notes.. wish I had more for you. Jojo

Amen !! I have a decent set of stemco and CR seal drivers for wheel seals including the wear sleeve driver for stemco's.. I can install either brand with confidence. definately stick with what has worked for years.. thanks GW..

i bet the wires are wrapped in that hard plastic woven loom. If there is good power coming from the dimmer switch, I bet there is a bad wire or 2 in the loom. probably nice and green.. does the harness run by the steering box and go to the left hood hinge area?

the wires are coming from the terminal strip on the firewall left of the steering shaft. they are 14 or 15 pin strips.

dont you have terminal strips under the hood for the lights and the horn?

sorry bud,, I have had an issue with pics for months..

bad dimmer switch? are the wires inside of a plug or just have female blade connectors on them and plugged into the dimmer?

so who makes National seals.. to me they are just orange colored CR seals.. with the same part number in some case's, Ie: 370025A and 380025A..

GW. I didnt research why the B Models I worked on had the inner seal, I just know that a good stemco seal on the inside did the trick. It modernized the ole; B-61.. and yes, when I replaced the rear wheel cyls in my ]48 KB-7, I used a modern wheel seal..

are you asking about the terminal strips on the firewall by the steering column? I have never worked on what you have.. just curious.

👍

J-37720-C Mack E9, E7, & E6 Roller Lifter & Tappet Holder Kit Alternative This tool retains the roller lifters when removing and installing the camshaft. It works on E-7 EUP (Electronic Unit Pump) and tappets in the Mack E-9, E-7, and E-6 Engines. Inclues High-Quality Aftermarket Alternatives of: J-42425-3 Magnet Cap x16 J-42425-4 Bottom Rod x16 J-37720-5A Top Rod x16 J-37720-6A Grommet Kit x1 J-37720-13A Magnet x16 AM-J-37720-C Manufacturer Aftermarket Brand Aftermarket Storage Code W-46, W-42 J-37720-C Mack E9, E7, & E6 Roller Lifter & Tappet Holder Kit Alternative SKU# 1664-L Here are 3 essential tools to do a basic cam job. since it is running good I didnt list a couple others. Jojo

Cam has to come out.. and ther are specific procedures that have to be followed.. You can NOT press the gear back on cold..

did you put the off-set cam key in the cam shaft? the 400 has a staight key.. PAI EKY-3179 MACK 54GC29 CAMSHAFT WOODRUFF KEY (.022" OFFSET) (E7) (OEM)

I say... All Good.. Biden is dead, I mean,,, not running the country anymore, I mean,,, O'bama has a new puppet.. I guess this thread can be called.. ''The Best of O'Bama''.

Bob, my answer to unwanted visitors, was a remote control driveway gate. I made it myself out of Lowe's chain link fence parts from the garden center.. It is NOT pretty, but it has been drawing a line for 8 years now. I have an electric gate operator that works just fine.. If I happen to se the God Squad ( nothing against Christians),,park on my street, I watch them walk up and down my road to see how to get to my door bell.. It's funny.. I have 400 + feet of frontage all fenced in..