Jump to content

Joey Mack

BMT Benefactor
 View Profile  See their activity

  • Posts

    8,975

  • Joined

  • Last visited

  • Days Won

    210

 Content Type 

Everything posted by Joey Mack

  1. Joey Mack
    download the svc. bulletin for a 9-2 code and follow the procedures for cleaning the grounds.. I bet you have a bad ground, or even bad wires in the harness, which can be fixed if you find the damaged wire(s).
  2. Joey Mack
    Today I saw that, J.B. had the 'Tea Bag' to say that if you show him a border security bill that works, he would sign it.... We had a plan, and HE... J.B. stroked his pen on day-1, and did away with it and 20 other bills and policies.. W.T.F.??
  3. Joey Mack
    There is a company called ''Atro'' I have been able to get torque rods from them. You may need to measure the length ''on-center'' to find the correct ones..
  4. Joey Mack
    Ooops... I forgot to welcome you to the Dog Pound.. Jojo
  5. Joey Mack
    I-Phone... I think thats the issue, not certain.
  6. Joey Mack
    yep, aerated fuel.. can you pump the hand primer before trying to start it, to see if it starts quicker, if the hand primer leaks, its no good.
  7. Joey Mack
    even with an air dryer, you need to pull the cables daily.. Air dryers do good if maintained, but most just forget they are there, and water still collects in the tanks.. Air dryer + pulling the cables on the drains will help a lot.. Jojo
  8. Joey Mack
    Yes Bob has sent pictures to me.. We are 'Kin' ya' know...
  9. Joey Mack
    I know we would love to see pictures of this Bus.. Jojo
  10. Joey Mack
    Good deal Bob. I see you can post pictures again.. 🍻
  11. Joey Mack
    Yes the bleeder is important and must face forward. After a few years of doing these, I just remove the plug on top of the front water manifold, right behind the thermostat housing. then you can pour the coolant in quickly. you can thread the plug back in about 1 turn so you dont make a big mess,,
  12. Joey Mack
    Fleetliner? What country are you in? I assume you have EUP's..
  13. Joey Mack
    Maybe you relieved an air pocket, and it improved the cooling.. there are Mack engines without coolant filters. Anyway, that's good..
  14. Joey Mack
    the EECU fuse is #40 in the box under the hood. 9-2 code is '' power reset without the key'' I lean towards a loose ground. yes, a 'wiggle' wire/fuse test may just point you to the issue..
  15. Joey Mack
    speed controller..
  16. Joey Mack
    It was a good day for sure..
  17. Joey Mack
    I bet the ''credit card'' is bad.. there is a fan resistor in the left side of the HVAC box.. look for the flat plug going into the box
  18. Joey Mack
    check the ground wires at the big bolt on the block in front of the starter.. Is the coolant low, below the sensor? does the shutdown light come on? it seems like the issue is when going uphill.. I wouldnt throw any parts at it yet. I bet its a loose/bad wire. yes, check fuel pressure, should be around 80 PSI.
  19. Joey Mack
    Paul, I have a large toaster oven in my shop. I can put it right next my work, and rock and roll..
  20. Joey Mack
    Bingo !!
  21. Joey Mack
    Oh Hell !!! Is that a Mortar ??
  22. Joey Mack
    It's All Good Bud... Jojo
  23. Joey Mack
    I own the rear main seal installer.. it works just fine..
  24. Joey Mack
    Well, if you want to make a million dollars with that truck.... Start with 2 million... Run away, run far away....
  25. Joey Mack
    the water filter just takes a small sample of water.. I highly doubt the issue is there.. Yes, cleaning/ rodding the radiator can prove well. Another possiblilty is pump cavitation. as you go along on this, I recommend you get the 2 pump gaskets, and pull the pump and inspect the impeller and the housing. When looking at the housing, ( the part that stays mounted to the engine) you are looking for pitting and grooves caused by air in the cooling system.. if you find that, you will need a new housing, cavitation will reduce coolant flow enough to raise engine temp.

BigMackTrucks.com

BigMackTrucks.com is a support forum for antique, classic and modern Mack Trucks! The forum is owned and maintained by Watt's Truck Center, Inc. an independent, full service Mack dealer. The forums are not affiliated with Mack Trucks, Inc.

Our Vendors and Advertisers

Thank you for your support!

Mack Related Links

Popular links

BMT Forum Logo

HTML tutorial
×
×
  • Create New...