41chevy

Water separator.

Congrats!!

Governor Mills says the the "front People keep touching their masks and the germs go from the hands to the plates. Heck Maine is even testing the sewerage for the Covid virus. do not know what thats about aside from the money trail.

Gideon is the one to worry about, higher income tax, gas tax to 40cents, 30% increase in diesel and heating oil tax, special taxes against Poland Springs and more aid and help for "refugees". Gideon supports the 4100 strikers a Bath Iron Works and wants to curtail logging. Most away from Southern Maine don't like those things but with our Ranked Choice Voting Collins will probably lose and Mills could be re elected with the Portland, Augusta and Orchid Beach votes.

Mack had problems with the connector terminal heating up and loosening causing a miss, oil eroding the insulation so the the harness will be brittle and the insulation will break off. See if you can locate Mack Service Bulletin SB222017 for diagnostics

Dang, thats a good looking unit! Has the can do attitude that Mack used to have not so many years ago.

Sadly it is all too real. Governor Mills said it is common sense to wear it that way so the droplets to travel down on the food as they would with a normal face shield..

Donate Maine Public Radio Mills Administration Updates COVID-19 Prevention Checklists For Food Businesses By Patty Wight • Aug 14, 2020 Most of the updates are just a few additions or clarifications to previously released checklists. For example, front-of-house staff in restaurants, convenience stores and fast food businesses who choose to wear face shields must now wear them upside down so that they are attached at the collar instead of the forehead, so that their breath is directed up, not down.

Looks like you need a BIGGER truck

Wow! Thats is a really sweet set up! Bet those LED reverse lights are bright too.

If Terry's idea doesn't work, soak it with PB Blaster let it sit over night and try again to wiggle it out like Terry said. Paul

I'd talk to Old Bill and heed his advise.

Looks really good from here. Any clue to why it was parked?

yes center-line, I really don't know if it is like the early and late R model with the length difference on the entire windshield end. Probably wouldn't make any difference other than appearance.

The CH hood is 1 1/2 to 1 3/4 inches longer than the CHN.

After you do the plug wires and road test it, if it still rough at hi speeds a few things can cause the issue. Point bounce, the flat springs do lose tension with age, ohm the primary and secondary winding's in the coils out. They can break down and at higher RPMs can cause a slight misfire. Check Primary side ohms from + to - terminals should have a value of .4 to 2 ohms. Check secondary ohm from + terminal ( - side if the system is still positive ground) to coil wire tower values should be from 6000 to 12000 ohms. I only mention how to check it because most techs are not familiar with old school systems. Paul

Good luck! Bet you stress level dropped a lot.

AC, NGK or Bosch as a 3rd choice. I've had so so luck with Champion over the past few years. Had to many fail for no reason.

Twin ignition 707 engine my info show the same plugs for both.

You won't get stopped using these balloons . . . http:// You're trying to correct the same person who learning I was married again to an Israeli congratulated us by posted a link to tell me that all Jewish people vote Democrap?

We had an Anton 225 land at Bangor on July 31 with an issue took off on August 2 for Prestwick,UK . The crew posted a pair of videos. Seemed to have a relatively short takeoff run. Impressive to say the least on the apron next to a few C130's I can link them if you like

https://www.redstate.com/nick-arama/2020/08/14/joe-biden-dives-headlong-off-the-deep-end-with-the-wacky-postal-conspiracy-against-trump/

any oil or water in the air tanks?

Best show some respect as shown below.

Let BLM do it they have close to 3/4 of a billion in assets now from the guilty white privilege soy boy liberals reparations