hatcity
-
Posts
4,826 -
Joined
-
Last visited
-
Days Won
26
Content Type
Profiles
Forums
Gallery
Events
Blogs
BMT Wiki
Collections
Store
Everything posted by hatcity
-
Summin hol ma beer, watch this . Saw one of those cheetahs on Ebay for about $250. Could use truck air to fill it. Just have to do the armstrong thing for the nuts
-
Yeah, thats what I have. Didn't think to ask type of trans.........DOH
-
Redneck engineering at iys finest
-
Drivers side, underneath, bout right under door hinge area. Mine needs a 1/2 inch ratchet head (square) and a little extension to loosen. It is in a tough area to see if lots of road debris. Mine also has a round flange type thing re; type of oil to use.
-
another vote for the pimpmobile. Just needs "diamond in the back, sunroof top" Change his handle to "Huggy Bear"
-
Very sorry, but is no different than a laborer with a hammer. Can he cut and fit a hip roof from stick? Can he build custom cabinets? THEN he is a good carpenter Right Bigen
-
Help Me Pick A Truck
hatcity replied to thirdcoaster's topic in Modern Mack Truck General Discussion
Here ya go http://cgi.ebay.com/ebaymotors/Mack-Toterhome-/110524017334?cmd=ViewItem&pt=Commercial_Trucks&hash=item19bbbeaab6 -
Didn't that used to have a ceeeeement mixer on it?
-
More pics would be OK. Oh, the truck aint bad either. Actually, that is a fine looking motor home. Bet you get a lot of crap at the campground. Drop in low and push the junk over to the side
-
Aint that the truth
-
Don't come thisaway. I'm paying 3.09/gal. All the local places are about the same Course I don't think the landfill road is even 10%. But the SCENERY is fantastic!!!
-
Yeah thats a problem being skinny and all. Thought of swinging boom over front and attach a strap to use as a pulley system. Problem is moving to side to set down and pick up new one. Thats it. i'm getting a service truck with a crane
-
Thanks all. the torque arm only was a PIA with the body propped up a little. 3/4 breaker to get started and tightened. As for the radiator, talked to a local shop today. $575 plus $15 shipping, and about $200 to do the job. Mack was looking at $1200 just for the rad. They are checking to make sure it is an in/out replacement
-
E-bay had a 1950 LJX partially redone. Asking 15,000 HK's brother in law lives in Danbury, CT where the truck was located Didn't look too bad but too much $$$ for me
-
I got an 01 Vision. If it's the same, pass. side of unit is duct work. couple torx screws to remove. Filter (if there is one) is between duct and unit. Mine was FULL of leaves, crap. i check it monthly. yep hitting 80's and up here in FLA
-
Yep thats the arm I'm talking about. Looked easy enough. 600 for rad. sounds pretty good. Mack told me the replacement (alum/plastic) was about 1200+ depending on yhe truck. I asked him "so it can fail again?" he laughed
-
need to replace torque arm. Actually need bushing replaced but Mack only sells the complete arm. How difficult to change, providing everything still in line. Don't look tough but just want to be sure. Also, where can I get a metal radiator? Alum/plastic is starting to leak.
-
Pic #7 "water stain" clearly visible I understand price is a big issue for you, but, why an '87 or Fruitloop even. Get a
-
Your mattress has a piss stain.
-
Crack #1 line. No manual pump?
-
Rowdy bumped up the idle, put the body in gear, and BAILED. Must have good insurance
-
Where are you planning on finding a driver?yrs. exp? record? rate of pay?maint. costs and who does it? workers Comp!!! Alot more to it than just buying the truck. I applaud your desire to get a truck but these are questions you really need to answer to see if it will work.
-
Don't know the whole answer but, depends on the clearance around the bumper/ fender. also, if you go aluminum, make sure you get LONGER studs
-
Thanks for you support Rob. LL, where you been? Used to be posterboy for post whore j/k Just messin with ya. Some people DO take 6,7, 10 years to leave college. some have a degree, some don't. All BS aside, how did you make out with that broker job thing? Is that the company you pratice backing at? Speaking of "public aid" i hope the gov't makes good use of the friggin check I had to write today
-
Oh I know a few like that. Just don't have the rack like you. GUN RACK
BMT Forum Logo
