terry
-
Posts
2,344 -
Joined
-
Last visited
-
Days Won
1
Content Type
Profiles
Forums
Gallery
Events
Blogs
BMT Wiki
Collections
Store
Everything posted by terry
-
Oh yeah they were made, went and sat in one today! terry
-
i posted in the wanted section, but thought there is more traffic here, looking for a D42 emblem, or somebody you know that might have one, yes very hard to find! terry
-
Looking for a D42 emblem, i know it's a rare one! terry or somebody that might have one.
-
Air cleaner question.
terry replied to Licensed to kill's topic in Antique and Classic Mack Trucks General Discussion
the upper one is a later set up, don't know exactly the cut off year when they went with it, as far as gas engines i have seen them with external air cleaner on the overhead engines and a oil bath one on top of the carburetor on the flathead engines. terry -
This is the real early six speed, the front box was a basic 5 speed with reverse, and the back box was a low and direct to use with the 4.17 rears, and the the overdrive had a direct and a wide overdrive to use with the slower rears that were used with the tri and quads transmissions. terry
-
Hydraulic clutch??
terry replied to Licensed to kill's topic in Antique and Classic Mack Trucks General Discussion
I think that draggon wagon that posted up above is that Tom, terry -
Looking for a tractor or dump, single or tandem axle? need to be a little more specific.😄 terry
-
most floor pans are bolted in, some even around foot valve, depends what model he is talking about. terry
-
That .68 overdrive trans is a 2060,2070 or 2080 series transmission, too much overdrive for 4.17 rears, the 2090 would be a real good trans for you. terry
-
Are you sure you are getting the numbers off the transmission case correct? A X107 is a direct transmission. with 4.17's it will top out about 60MPH. depending on your top RPM's. terry
-
34k Camelback saddle cap insulator spacers
terry replied to Lmackattack's topic in Driveline and Suspension
I believe them spacers were only used on the steel caps, they probably would chew up an aluminum cap. terry -
How much for labor ?
-
thanks for that info. terry
-
I have a set of six of cummins reman injectors says PTD injector part number 3018840PX, if anybody can figure out what these are for? would sell them real reasonable if you can use them. terry
-
he said it was the line going to the govenor. probably the one to the compressor. terry
-
Sounds like the beam might be wollered out! terry
-
I second that camel back, terry
-
That trans and rear ratio should work good, but have absolutley no experience with that suspension, i'am sure somebody will comment on it here. terry
-
Was it making this noise before the oil change? terry it would be a good idea to put the correct oil in it! I believe the 50 weight syn. was for the fuller trans. A lot of viscosity difference between them two oils.
-
How to remove block heater off a E6 block?
terry replied to Vladislav's question in Mack Truck Q & A
If there are two allen head screws, unscrew these and should pop out, they have a little curved piece on each one that clamps the heater down to the block when you screw them down. -
Hows norm doing/ bought a B733 from him some years ago, a real terrific guy.
-
If you look on his very first post it says the truck is sold.
-
Now that is a hood! terry
-
I have only seen that seven speed trans used with 300 engines. terry
-
Yeah i once had a DM dump with a 285 that would turn 2300 RPM'S, with the 1070 12 spd, and 4.17 rears, it would bury the 80 MPH speedometer. terry
BMT Forum Logo
