Jump to content

terry

Pedigreed Bulldog
 View Profile  See their activity

  • Posts

    2,277

  • Joined

  • Last visited

  • Days Won

    1

 Content Type 

Everything posted by terry

  1. terry
    has the little newer clearance lights, hood hinge and the bigger mack lettering. could be up into the 80's terry
  2. terry
    looking like a truck again!!👍👍 terry
  3. terry
    I always thought the ST meant six wheel tractor. terry
  4. terry
    I would guess maybe the tower rotted out, they will rust out where the tower sides come down to the trunnion. terry
  5. terry
    On the window and opener handles the round trim ring right next to the door panel is a spring loaded ring you push in to see the pin. terry
  6. terry
    Should be a spring loaded ring on the inner part, have to push in hard to see pin holes. terry
  7. terry
    looks to be in pretty good shape, should be brought back to life! terry
  8. terry
    So did they give you a solid estimate? terry
  9. terry
    I don't know if the one j hancock has there is the multi piece one where you cut the old out and install new one in pieces. if your replacement is a one piece one, you have to set dump box off, cut rear hinge off remove rear crossmembers and loosen front ones spread frame and slide tandems out, then take it apart. It's a whole bunch of heavy work!! terry
  10. terry
    tractor or dump a lot of labor between the two. terry
  11. terry
    chock the wheels and slide under while somebody touches brakes, could be a multitude of things, from front to rear!! terry
  12. terry
    Is that the door under the bulldog? pretty rare hood? must have a truck waiting for it? terry
  13. terry
    Each box has its own overdrive, when you start off in 1st in the main and first in the aux, shift the four in the aux. put the main in second and put the aux.in low split, then direct and then hi split, when splitting the main box you do not use lo-lo in the aux. do this to 4th in the main and the aux. is in hi split. your last shift is fourth in the main and hi split in the aux to fifth in the main. sounds confusing but just takes some practice. terry
  14. terry
    have to disagree with a few things, I have seen lots of early RD's with single frames, but the frames are thicker and deeper than a R model. And have seen lots of 38k suspension with factory double frames. I think a lot of the differences are the area they were ordered for, for everyone ordered one way you can find a different one the other way. terry
  15. terry
    Should be right behind the fill plug. terry
  16. terry
    Generally the first thing you hit with wrong backspace is tie rod end. terry
  17. terry

    B61T 36347

    terry replied to eddeere's topic in Truck Stories

    top notch job!! terry👍👍
  18. terry
    Can you imagine the hydraulic nightmares with them trucks! terry
  19. terry

    MEMORIAL DAY.

    terry replied to 41chevy's topic in Odds and Ends

    😢😢😢
  20. terry

    MEMORIAL DAY.

    terry replied to 41chevy's topic in Odds and Ends

    I think it's a beautiful picture, as for your nam brothers comment I was there in "69", sure was a tragic waste of young men ! terry
  21. terry

    Site seeing

    terry replied to B MACK's topic in Odds and Ends

    beautiful country!👍👍👍 terry
  22. terry
    Also has the real old fuel tank bracket and strap. terry
  23. terry
    wedge brakes are terrific when everything is new, but on a truck that has been for years everything gets stuck in them. biggest problem is keeping the self adjusters working. terry
  24. terry
    is it a runner? terry
  25. terry
    Have not seen one of them air filters for a long time, cab don't look to be in to bad a shape. terry

BigMackTrucks.com

BigMackTrucks.com is a support forum for antique, classic and modern Mack Trucks! The forum is owned and maintained by Watt's Truck Center, Inc. an independent, full service Mack dealer. The forums are not affiliated with Mack Trucks, Inc.

Our Vendors and Advertisers

Thank you for your support!

Mack Related Links

Popular links

BMT Forum Logo

HTML tutorial
×
×
  • Create New...