DailyDiesel Posted June 23, 2013 Share Posted June 23, 2013 All right, since we have some professional construction types here I have a question regarding road "repairs". What is the logic or reason for milling the road about every 10 yards to place a strip of new asphalt from shoulder to shoulder? Each strip is about a foot long. God help you if have a bad back on this portion of 81 outside of Whittney Point, NY. Quote www.dailydieseldose.com Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-190513 Share on other sites More sharing options...
RFCDrum Posted June 23, 2013 Author Share Posted June 23, 2013 Good question. Need Tim's opinion for that one. Rob Quote Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-190514 Share on other sites More sharing options...
Timothy Maikshilo Posted June 24, 2013 Share Posted June 24, 2013 Are you with us?? I thought maybe you were shacking up with the moose in the woods. Yes my friend I've been 2.5 hours from home all week and headed back at 2:30 AM and I hope not to see any moose or deer on the way!All right, since we have some professional construction types here I have a question regarding road "repairs". What is the logic or reason for milling the road about every 10 yards to place a strip of new asphalt from shoulder to shoulder? Each strip is about a foot long. God help you if have a bad back on this portion of 81 outside of Whittney Point, NY.It sound's like they are trying to take the high spots out of the road....but you would only do this in the travel lane and one foot does not allow time for the milling machine to react. Unless they were using a skid steer trimmer to run side ways to the road.Good question. Need Tim's opinion for that one. Rob Rob, My answer to this would be Band aid!!! Seen here we trimmed 4 feet wide for the over lay to butt against the shoulder Quote Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-190594 Share on other sites More sharing options...
RFCDrum Posted June 24, 2013 Author Share Posted June 24, 2013 Could be where the seams were and they heaved up with the frost. They did that on the Quickway from Goshen NY to Chester then milled it afterward to get a consistent grade. Quote Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-190596 Share on other sites More sharing options...
RFCDrum Posted June 24, 2013 Author Share Posted June 24, 2013 Still think you are shacking up with them swamp donkeys. Quote Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-190597 Share on other sites More sharing options...
Timothy Maikshilo Posted June 25, 2013 Share Posted June 25, 2013 Still think you are shacking up with them swamp donkeys. Just got back from Brattleboro and saw this off of Rt. 5 in Rockingham, Vt. Not to bad looking and typical Vermont double frame issues and no swamp donkeys! Did not see a one of um! 2 Quote Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-190958 Share on other sites More sharing options...
RFCDrum Posted June 26, 2013 Author Share Posted June 26, 2013 Too hot for them. Quote Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-191157 Share on other sites More sharing options...
Popular Post 2stacksuperdog Posted July 22, 2013 Popular Post Share Posted July 22, 2013 Heres the milling machine we were working with in Manchester today.and heres a picture of dumping out the millings just because everybody likes a picture of a superliner at work! 4 Quote Matt Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-195349 Share on other sites More sharing options...
hatcity Posted July 22, 2013 Share Posted July 22, 2013 A&J-started as two Portegese guys doing driveways around Danbury.Heard they were able to reap some benefits of the governments work ready politics. Quote Success is only a stones throw away.................................................................for a Palestinian Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-195355 Share on other sites More sharing options...
2stacksuperdog Posted July 22, 2013 Share Posted July 22, 2013 A&J-started as two Portegese guys doing driveways around Danbury.Heard they were able to reap some benefits of the governments work ready politics.They got a lot of equipment now. They are a minority so they get the work. 2 Quote Matt Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-195358 Share on other sites More sharing options...
Popular Post Timothy Maikshilo Posted October 5, 2013 Popular Post Share Posted October 5, 2013 Hi All! Been a busy year and still going strong! Working on a mill and fill in Franconia, NH now till snow....which could be any day!Also drove a GU for a couple days while waiting for the paving crew to come off of nights 5 Quote Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-210173 Share on other sites More sharing options...
j hancock Posted October 5, 2013 Share Posted October 5, 2013 Hey Tim! Thought your GPS was broken and you got lost. Quote JimIt doesn't cost anything to pay attention. Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-210184 Share on other sites More sharing options...
Red Horse Posted October 5, 2013 Share Posted October 5, 2013 Back to the question about a one foot band every 10 yards?? Assume it is width of roadway? I would guess this was a concrete road that was repaved with asphalt-could they be doing the expansion joints in original concrete that have heaved? Quote Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-210195 Share on other sites More sharing options...
Red Horse Posted October 5, 2013 Share Posted October 5, 2013 As you guys get excited about milling machines, about a month ago I'm southbound on Mass I-495 around exit 13 or so. Traffic starts slowing. detached low boy is on shoulder like they are going to load something. Then just other side of bridge abutment is Agreggate Industries machine on its side-underside facing the road- OOpps! My guess is they were positioning to load and shoulder had quite a slope to it-as well as soft ground. Don't think anyone got hurt other than ego as only news coverage was the traffic slowdown. Quote Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-210196 Share on other sites More sharing options...
Timothy Maikshilo Posted October 5, 2013 Share Posted October 5, 2013 Hey Tim! Thought your GPS was broken and you got lost.Yes...I haven't had time for anything but work, up at 3:30 to 4:00 AM home at 8:00 or so PM. Enough time to sent in my reports then bed!As you guys get excited about milling machines, about a month ago I'm southbound on Mass I-495 around exit 13 or so. Traffic starts slowing. detached low boy is on shoulder like they are going to load something. Then just other side of bridge abutment is Agreggate Industries machine on its side-underside facing the road- OOpps! My guess is they were positioning to load and shoulder had quite a slope to it-as well as soft ground. Don't think anyone got hurt other than ego as only news coverage was the traffic slowdown.To bad! Top heavy machine and then add a tank of water and full fuel tank to boot, would make things happen quickly. As for milling every ten yards, I have no ideas on this....would make more sense to just mill the whole thing out? Here is a pull off that we paved in then it was decided to mill it up the next day in Alburg. Quote Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-210198 Share on other sites More sharing options...
Timothy Maikshilo Posted October 12, 2013 Share Posted October 12, 2013 Franconia, N.H. milling going well, starting to wind downMike and Tammy getting loadedTammy's KW leading the pack! Quote Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-211320 Share on other sites More sharing options...
RFCDrum Posted October 12, 2013 Author Share Posted October 12, 2013 Still need a pic of Tammy. Quote Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-211347 Share on other sites More sharing options...
Timothy Maikshilo Posted October 12, 2013 Share Posted October 12, 2013 Still need a pic of Tammy. I'll see what I can do! Quote Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-211348 Share on other sites More sharing options...
RFCDrum Posted October 12, 2013 Author Share Posted October 12, 2013 You know we like wimmins! Tell her it is for a good cause. 1 Quote Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-211350 Share on other sites More sharing options...
Timothy Maikshilo Posted October 20, 2013 Share Posted October 20, 2013 You know we like wimmins! Tell her it is for a good cause.OK Rob, Tammy let me take her picture for a good causeShe is a great driver and takes care of her truck like no other. Quote Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-212414 Share on other sites More sharing options...
j hancock Posted October 20, 2013 Share Posted October 20, 2013 How about a picture of her NEXT to her truck?What a tease.Geeesh, you are killing us! 1 Quote JimIt doesn't cost anything to pay attention. Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-212419 Share on other sites More sharing options...
REEL ADDICTION Posted October 20, 2013 Share Posted October 20, 2013 I hate when they have us line the truck next another so they could keep the milling machine going. Milling all over the side of the truck Quote Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-212428 Share on other sites More sharing options...
theakerstwo Posted October 20, 2013 Share Posted October 20, 2013 I hate when they have us line the truck next another so they could keep the milling machine going. Milling all over the side of the truckAND IT DONT TAKE ALL DAY TO STOP UP THE AIR CLEANERS. Quote glenn akers Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-212437 Share on other sites More sharing options...
Timothy Maikshilo Posted October 20, 2013 Share Posted October 20, 2013 How about a picture of her NEXT to her truck?What a tease.Geeesh, you are killing us!The best I could do she is always on the move! Quote Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-212439 Share on other sites More sharing options...
Timothy Maikshilo Posted October 20, 2013 Share Posted October 20, 2013 I hate when they have us line the truck next another so they could keep the milling machine going. Milling all over the side of the truckA good operator shuts off his belt when switching trucks and spills none, maybe pass that along to them.Number one ground man and operator here! 2 million SY through the Wirtgen this year! Quote Link to comment https://www.bigmacktrucks.com/topic/30486-some-milling-for-tim/page/5/#findComment-212440 Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.