mack mhe9 Posted August 9, 2013 Share Posted August 9, 2013 Who else can spot the problem. Unloaded at 10 pm in Bedford Pa. These guys where next at Penn diesel. They said it ok there only going to VA. Good luck. Quote Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/ Share on other sites More sharing options...
slpwlker Posted August 9, 2013 Share Posted August 9, 2013 Height control. Idk other then being morons it is going to be one hell of a ride for them Quote Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198852 Share on other sites More sharing options...
Popular Post daveigou Posted August 9, 2013 Popular Post Share Posted August 9, 2013 Don't know which is worse, their weight distribution is really bad, or their crack problem. 5 Quote See my Flickr photostream page http://www.flickr.com/photos/96692978@N05/ Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198860 Share on other sites More sharing options...
fullfuel01 Posted August 9, 2013 Share Posted August 9, 2013 I've done stupid thing, but this, I'll pass.. that poor 2wd Ford would really stick to the wet asphalt. Quote Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198864 Share on other sites More sharing options...
rsb502 Posted August 9, 2013 Share Posted August 9, 2013 Seems I remember a Freightliner condo being around 13' tall, wouldn't a 3' tall trailer get that closer to 16'? I won't comment on the weight distribution its been said. Quote "Any Society that would give up a little LIBERTY to gain a little SECURITY will Deserve Neither and LOSE BOTH" -Benjamin Franklin"If your gonna be STUPID, you gotta be TOUGH" "You cant always get what you want, but if you try sometimes you get what you need" Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198865 Share on other sites More sharing options...
JTFormula Posted August 9, 2013 Share Posted August 9, 2013 The crack issue has affected thier ability to think logically. Did this guy have a foreign accent? Sounds like the same outfit that picked up at my place a few weeks ago with an overloaded f350. I posted pictures in another thread. Quote ~ JT Burkard ~ AKA Sweaty Mackwww.jtresto.com www.wickedreputation.netwww.jonathanthomasmotorcars.com Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198866 Share on other sites More sharing options...
2stacksuperdog Posted August 9, 2013 Share Posted August 9, 2013 i know a guy that said he put a triaxle on ones of those trailers with his dodge dually pulling it. 1 Quote Matt Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198870 Share on other sites More sharing options...
mack mhe9 Posted August 9, 2013 Author Share Posted August 9, 2013 The set up was licensed out of Cal. And it Said not for hire on the door. I tried to explain it was all wrong in all the ways as described above and then some but I don't think they understood my English accent. Yes they where at 14.6 high. When you leave Penn Diesel it's about a 9% hill up to the light. I think I did the right thing and called the state police they said they would send a car buy to check it out but there's nothing they could do. 1 Quote Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198879 Share on other sites More sharing options...
NoClueJoe66 Posted August 9, 2013 Share Posted August 9, 2013 First scalehouse hopefully stopped them, before someone got seriously hurt.... Quote This message was brought to you by Hargraves Potted Meat Product. Chopped full of "Peckers & Lips" since 1933 - John Boy & Billy Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198880 Share on other sites More sharing options...
Terry T Posted August 9, 2013 Share Posted August 9, 2013 My thought is they never made the scale house, about the time they hit 40 I would think that trailer would start whipping back and forth & they'd be lucky if they only ended up jack-knifed in the ditch... Quote Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198883 Share on other sites More sharing options...
NoClueJoe66 Posted August 9, 2013 Share Posted August 9, 2013 Very true Quote This message was brought to you by Hargraves Potted Meat Product. Chopped full of "Peckers & Lips" since 1933 - John Boy & Billy Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198886 Share on other sites More sharing options...
rsb502 Posted August 9, 2013 Share Posted August 9, 2013 My thought is they never made the scale house, about the time they hit 40 I would think that trailer would start whipping back and forth & they'd be lucky if they only ended up jack-knifed in the ditch...Well that would be the way it would happen if this was an isolated incident just trying to get home, however those that do this every day seem to be immune from the law I see em all the time and they just seem to keep on going without consequence. Quote "Any Society that would give up a little LIBERTY to gain a little SECURITY will Deserve Neither and LOSE BOTH" -Benjamin Franklin"If your gonna be STUPID, you gotta be TOUGH" "You cant always get what you want, but if you try sometimes you get what you need" Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198887 Share on other sites More sharing options...
Freightrain Posted August 9, 2013 Share Posted August 9, 2013 Too their defense, I don't think the weight is the real issue. What's the truck? 13K? 14K? Throw 2K for the trailer. Not really all that overweight to be pulled by the PSD. My race trailer is 14K and I'm light compared to some of the 45-50ft trailers out there(and I pulled it with '96, 00 and 2000 F350's). Look at some of the 5'r campers these guys are pulling with single wheel 3/4 ton trucks. They did put the motor back over the axles(smarter move), as the truck would not support that kind of pin weight. My trailer was 3K on the pin and handled perfect. It ran up Fancy gap in 6th gear just feathering the throttle.Height? Ya, probably gunno get some power lines or maybe a brigde somewhere along the line.Rob brought his R model home on a similar trailer with his crusty Dodge. Quote Larry 1959 B61 Liv'n Large...................... Charter member of the "MACK PACK" Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198888 Share on other sites More sharing options...
mack mhe9 Posted August 9, 2013 Author Share Posted August 9, 2013 Yes I think gross would be fine, but 9000 steer axle sitting on the very back edge off the trailers going to wreak havoc with handling. And when they tow backward the air fights to get around the cab causing it to push side to side. It will be a handful. 2 Quote Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198891 Share on other sites More sharing options...
Terry T Posted August 9, 2013 Share Posted August 9, 2013 Yes I think gross would be fine, but 9000 steer axle sitting on the very back edge off the trailers going to wreak havoc with handling. And when they tow backward the air fights to get around the cab causing it to push side to side. It will be a handful.Actually I think they are carrying more than just 9K behind the trailer axles when you take into consideration the slope of the trailer & the afore mentioned air pushing on the back side of that tractor.I once loaded my Kawasaki Mule & Pop-up camper on a tandem axle open car trailer. I thought I had the camper axle close enough to the trailer axles but I didn't. I made it to the 60mph speed zone & was real close to being upside down in the median of US 30 only 6 miles from where we started. I reloaded by backing the camper onto the trailer then running the Mule up some ramps we had with us over the tongue of the camper moving 95% of the weight over the axles and onto the tongue. A much nicer ride for the other 494 miles. The below picture was after the reload. 2 Quote Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198905 Share on other sites More sharing options...
NoClueJoe66 Posted August 9, 2013 Share Posted August 9, 2013 Too their defense, I don't think the weight is the real issue. What's the truck? 13K? 14K? Throw 2K for the trailer. Not really all that overweight to be pulled by the PSD. My race trailer is 14K and I'm light compared to some of the 45-50ft trailers out there(and I pulled it with '96, 00 and 2000 F350's). Look at some of the 5'r campers these guys are pulling with single wheel 3/4 ton trucks. They did put the motor back over the axles(smarter move), as the truck would not support that kind of pin weight. My trailer was 3K on the pin and handled perfect. It ran up Fancy gap in 6th gear just feathering the throttle.Height? Ya, probably gunno get some power lines or maybe a brigde somewhere along the line.Rob brought his R model home on a similar trailer with his crusty Dodge.Very good point Larry.....Just wondering, but uh if the truck they are hauling has stacks behind the sleeper was they smart enough to tape the openings up? Correct me if I'm wrong, but won't the air going into the exhaust mess the turbo up with the fin going backwards? I've always heard that but never knew... Quote This message was brought to you by Hargraves Potted Meat Product. Chopped full of "Peckers & Lips" since 1933 - John Boy & Billy Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198909 Share on other sites More sharing options...
masterwelder Posted August 9, 2013 Share Posted August 9, 2013 Too their defense, I don't think the weight is the real issue. What's the truck? 13K? 14K? Throw 2K for the trailer. Not really all that overweight to be pulled by the PSD. My race trailer is 14K and I'm light compared to some of the 45-50ft trailers out there(and I pulled it with '96, 00 and 2000 F350's). Look at some of the 5'r campers these guys are pulling with single wheel 3/4 ton trucks. They did put the motor back over the axles(smarter move), as the truck would not support that kind of pin weight. My trailer was 3K on the pin and handled perfect. It ran up Fancy gap in 6th gear just feathering the throttle.Height? Ya, probably gunno get some power lines or maybe a brigde somewhere along the line.Rob brought his R model home on a similar trailer with his crusty Dodge.If that trailer is a tandem dully- you're looking at 5 or 6k right there for the trailer. My day cab tractor is 16.5k . That is 21.5k conservatively with my truck! Behind a 10k truck?? Even if that is loaded properly it's quite a load. Quote Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198910 Share on other sites More sharing options...
mack mhe9 Posted August 9, 2013 Author Share Posted August 9, 2013 Yes the trailer was a tandem dully. 8 tires Quote Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198916 Share on other sites More sharing options...
rsb502 Posted August 9, 2013 Share Posted August 9, 2013 if that Freightshaker has a 12L Detroit its gonna weigh about 16,000, add 5k for the trailer you get 21k that is probably good on that trailer maybe 1k over but not more than I have hauled. However loaded like it is they have more like 60% of the weight of the truck behind the axles and the added forces of the wind on the back of that sleeper with the side fairings keeping it in, then add the height of 14'6" and..........., seems if they died in a fiery crash on the trip we wouldnt be losing much, Im just sayin.Oh the turbo thing is actually an issue of the turbo spinning with no lubrication, not spinning backwards, when the engine is off so is the turbos oil supply and most turos dont have bearings they have bushings and they actually float on a thin layer of oil that being why they need to be balanced properly, no oil means metal to metal contact. 1 Quote "Any Society that would give up a little LIBERTY to gain a little SECURITY will Deserve Neither and LOSE BOTH" -Benjamin Franklin"If your gonna be STUPID, you gotta be TOUGH" "You cant always get what you want, but if you try sometimes you get what you need" Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198920 Share on other sites More sharing options...
mack mhe9 Posted August 9, 2013 Author Share Posted August 9, 2013 If the exhausts pointed int the wind I tape them up. Like 84 said its spinning with no lubracation and a mile or two I wouldn't worry but after 600 miles at hwy speeds its turning an awful lot. Quote Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198926 Share on other sites More sharing options...
hatcity Posted August 9, 2013 Share Posted August 9, 2013 Dey gonna make it a chop top.........at the first bridge 1 Quote Success is only a stones throw away.................................................................for a Palestinian Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198927 Share on other sites More sharing options...
Green Dash Posted August 9, 2013 Share Posted August 9, 2013 Hopefully DOT was at Breezewood to protect these guys from themselves. Quote Jim Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198929 Share on other sites More sharing options...
Popular Post masterwelder Posted August 9, 2013 Popular Post Share Posted August 9, 2013 Well you know the DOT... always around when you don't need them, and never around when you do.Me personally, I very rarely need them around. 3 Quote Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198940 Share on other sites More sharing options...
NoClueJoe66 Posted August 9, 2013 Share Posted August 9, 2013 If the exhausts pointed int the wind I tape them up. Like 84 said its spinning with no lubracation and a mile or two I wouldn't worry but after 600 miles at hwy speeds its turning an awful lot.Thats what I thought...thank you Quote This message was brought to you by Hargraves Potted Meat Product. Chopped full of "Peckers & Lips" since 1933 - John Boy & Billy Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198954 Share on other sites More sharing options...
rsb502 Posted August 10, 2013 Share Posted August 10, 2013 Well you know the DOT... always around when you don't need them, and never around when you do.Me personally, I very rarely need them around.You meant......always around when you don't want them, and never around when you do. Quote "Any Society that would give up a little LIBERTY to gain a little SECURITY will Deserve Neither and LOSE BOTH" -Benjamin Franklin"If your gonna be STUPID, you gotta be TOUGH" "You cant always get what you want, but if you try sometimes you get what you need" Link to comment https://www.bigmacktrucks.com/topic/32268-i-see-the-problem/#findComment-198989 Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.