cxn613 Posted May 29, 2014 Share Posted May 29, 2014 1995 CL 613 with 427 and inline injection pump cuts in and out while pulling empty or loaded. Only acts up for short time then goes back to normal. Tried new fuel filters and new lift pump and still same thing. Was wondering something with pump or injectors or something electrical like the throttle pedal? Quote Link to comment https://www.bigmacktrucks.com/topic/35897-cl-613-cuts-in-and-out/ Share on other sites More sharing options...
wheeler73 Posted May 30, 2014 Share Posted May 30, 2014 Does the EML come on? Most likely electrical. I have seen a lot of issues with the pump connector and wiring. Wiggle the pump connector and wiring with the truck running and see if it cuts out. 1 Quote Link to comment https://www.bigmacktrucks.com/topic/35897-cl-613-cuts-in-and-out/#findComment-247316 Share on other sites More sharing options...
cxn613 Posted June 3, 2014 Author Share Posted June 3, 2014 Does anybody have a schematic of that plug? I pulled the plug apart and the one terminal had the plastic guide broke off and the spade is discolored. The two wires going in and out of the plug at that position have a zip tie on then as if its been a problem for the previous owner. Thanks Quote Link to comment https://www.bigmacktrucks.com/topic/35897-cl-613-cuts-in-and-out/#findComment-247901 Share on other sites More sharing options...
wheeler73 Posted June 4, 2014 Share Posted June 4, 2014 Very common to see. I usually see tye plug bypassed and the harness hardwired. I will see if I can get a diagram for you tomorrow. Quote Link to comment https://www.bigmacktrucks.com/topic/35897-cl-613-cuts-in-and-out/#findComment-247937 Share on other sites More sharing options...
rw613 Posted June 5, 2014 Share Posted June 5, 2014 that is the best place to start Quote Link to comment https://www.bigmacktrucks.com/topic/35897-cl-613-cuts-in-and-out/#findComment-248049 Share on other sites More sharing options...
cxn613 Posted June 5, 2014 Author Share Posted June 5, 2014 Thanks for the replies. I cut the wires on either side of plug and used a sealed connector and heat shrink to reconnected them. Before I did this I could get the truck to misfire while idling while moving the plug around. Now it seems to idle fine, going for test drive tomorrow. Thanks Quote Link to comment https://www.bigmacktrucks.com/topic/35897-cl-613-cuts-in-and-out/#findComment-248064 Share on other sites More sharing options...
cxn613 Posted June 6, 2014 Author Share Posted June 6, 2014 Took for test drive and still acts up. Noticed it only cuts in and out when pedal is pushed all the way down, let off pedal a little bit and it runs smooth. Could this be a peddle issue or something at pump. Is there a way to check the pedal for intermittent voltage? Thanks Quote Link to comment https://www.bigmacktrucks.com/topic/35897-cl-613-cuts-in-and-out/#findComment-248216 Share on other sites More sharing options...
theakerstwo Posted June 6, 2014 Share Posted June 6, 2014 You need to go to some one with a reader so they can monitor the ecm. Quote glenn akers Link to comment https://www.bigmacktrucks.com/topic/35897-cl-613-cuts-in-and-out/#findComment-248264 Share on other sites More sharing options...
rolloffron Posted June 10, 2014 Share Posted June 10, 2014 i have a cl 700 w/ a 427 did the same thing,replaced fuel filters - no change, cleaned and greased that plug no change,change main fuel line to the pump from the tank and ran injector cleaner thru it, goes like a rocket now.hope that helps you 1 Quote Link to comment https://www.bigmacktrucks.com/topic/35897-cl-613-cuts-in-and-out/#findComment-248692 Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.