carlotpilot Posted June 6, 2018 Author Share Posted June 6, 2018 12 hours ago, keg1 said: I just got my 78 Dodge pickup with 440 state inspected last Friday first time in six years and went to drive it to work on Tuesday and motor came apart. Haven't had time to look at it but pieces are sticking through the oil pan. ouch someding wong Quote Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400121 Share on other sites More sharing options...
41chevy Posted June 7, 2018 Share Posted June 7, 2018 Rod bolts are a notorious weakness on non Hi-Po big blocks. I personally always replace when I get an older 383 or 440. Non H-Po Chrysler went down in rod bolt shank diameter for some reason and than knurled it to fit the bolt hole in the rods. Quote "OPERTUNITY IS MISSED BY MOST PEOPLE BECAUSE IT IS DRESSED IN OVERALLS AND LOOKS LIKE WORK" Thomas Edison “Life’s journey is not to arrive at the grave safely, in a well preserved body, but rather to skid in sideways, totally worn out, shouting ‘Holy shit, what a ride!’” P.T.CHESHIRE Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400170 Share on other sites More sharing options...
keg1 Posted June 10, 2018 Share Posted June 10, 2018 (edited) Pulled motor out today. Took pan off, a pushrod, some lifter pieces, other small pieces and about a 3 inch chunk of cam fell out. The block is also vented like the pan. I think a 2 pack of jb weld and I'll be good to go. Edited June 10, 2018 by keg1 Added more Quote Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400356 Share on other sites More sharing options...
j hancock Posted June 11, 2018 Share Posted June 11, 2018 After the JB Weld, you can smooth out the job with a gallon of All Metal.... 1 Quote JimIt doesn't cost anything to pay attention. Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400360 Share on other sites More sharing options...
carlotpilot Posted June 11, 2018 Author Share Posted June 11, 2018 add a couple sticks of silver solder for the cam Quote Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400365 Share on other sites More sharing options...
Hobert62 Posted June 11, 2018 Share Posted June 11, 2018 17 hours ago, carlotpilot said: add a couple sticks of silver solder for the cam I'd Fire up the old stick welder and burn the cam back together. If you can get to it, keep it in the block so its held straight by the bearings. 1 Quote Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400397 Share on other sites More sharing options...
Freightrain Posted June 11, 2018 Share Posted June 11, 2018 Ohhhh, geez. That's BAD news. Nothing much worse then when the motor gods lets you see the rotating assembly from the OUTSIDE of the engine. My local shop dynoed a motor just a month or so back. Big Hemi motor built by someone else. They fired it up, made some baseline pulls. BAM!!!, rod came out the oil pan. They did a little looking and seems the assembler didn't get around to torquing all the rods? OOOHHH man. All the shop could do is wheel all the broken parts back to the guys pickup truck. Quote Larry 1959 B61 Liv'n Large...................... Charter member of the "MACK PACK" Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400404 Share on other sites More sharing options...
carlotpilot Posted June 11, 2018 Author Share Posted June 11, 2018 have not had time to mess with mine anymore maybe in a day or two i`ll get back into it Quote Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400408 Share on other sites More sharing options...
carlotpilot Posted June 11, 2018 Author Share Posted June 11, 2018 23 hours ago, keg1 said: Pulled motor out today. Took pan off, a pushrod, some lifter pieces, other small pieces and about a 3 inch chunk of cam fell out. The block is also vented like the pan. I think a 2 pack of jb weld and I'll be good to go. you don`t suppose you had a similar oil problem? Quote Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400409 Share on other sites More sharing options...
keg1 Posted June 12, 2018 Share Posted June 12, 2018 I never really did much with tearing into engines mainly because I don't know what I'm doing. Not that it matters but is there a way to know what went wrong first, cam broke and then rod broke or other way around? Quote Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400425 Share on other sites More sharing options...
41chevy Posted June 12, 2018 Share Posted June 12, 2018 (edited) 2 hours ago, keg1 said: I never really did much with tearing into engines mainly because I don't know what I'm doing. Not that it matters but is there a way to know what went wrong first, cam broke and then rod broke or other way around? Lay a bet the rod left first and the cam ran after it.Look at the rod bolts for bending or shearing. Mopar cams as a rule do not fail by breaking on their own. I can probably dig out a good short block 440 TNT engine, if I go home to look. Haven't been there since my wife died, should see if it's still o.k. . Edited June 12, 2018 by 41chevy Quote "OPERTUNITY IS MISSED BY MOST PEOPLE BECAUSE IT IS DRESSED IN OVERALLS AND LOOKS LIKE WORK" Thomas Edison “Life’s journey is not to arrive at the grave safely, in a well preserved body, but rather to skid in sideways, totally worn out, shouting ‘Holy shit, what a ride!’” P.T.CHESHIRE Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400431 Share on other sites More sharing options...
keg1 Posted June 15, 2018 Share Posted June 15, 2018 Ok thanks just curious as to what might have happened Quote Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400580 Share on other sites More sharing options...
Truck Shop Posted June 15, 2018 Share Posted June 15, 2018 On 6/11/2018 at 1:20 PM, Freightrain said: Ohhhh, geez. That's BAD news. Nothing much worse then when the motor gods lets you see the rotating assembly from the OUTSIDE of the engine. My local shop dynoed a motor just a month or so back. Big Hemi motor built by someone else. They fired it up, made some baseline pulls. BAM!!!, rod came out the oil pan. They did a little looking and seems the assembler didn't get around to torquing all the rods? OOOHHH man. All the shop could do is wheel all the broken parts back to the guys pickup truck. The motor gods got tired of being in the dark inside that engine and just wanted a window to peek out of. Truck Shop Quote One ping only Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400584 Share on other sites More sharing options...
41chevy Posted June 15, 2018 Share Posted June 15, 2018 2 hours ago, keg1 said: Ok thanks just curious as to what might have happened This is a 440 that was destroyed by the rod breaking mid point, the piece on the crank spun around and broke the cam in 3 pieces. Look at the last photo, the rod and wrist pin are still on the crank but not in their original cylinder. Hosted on Fotki Hosted on Fotki Hosted on Fotki Hosted on Fotki 1 Quote "OPERTUNITY IS MISSED BY MOST PEOPLE BECAUSE IT IS DRESSED IN OVERALLS AND LOOKS LIKE WORK" Thomas Edison “Life’s journey is not to arrive at the grave safely, in a well preserved body, but rather to skid in sideways, totally worn out, shouting ‘Holy shit, what a ride!’” P.T.CHESHIRE Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400586 Share on other sites More sharing options...
carlotpilot Posted June 15, 2018 Author Share Posted June 15, 2018 gone in 5 seconds Quote Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400587 Share on other sites More sharing options...
Truck Shop Posted June 15, 2018 Share Posted June 15, 2018 The B/RB blocks and cranks were pretty good but it is a engine that needs a set of Eagle Rods if your going to run one a little hard. At least a set of ARP rod bolts then have the housing bores checked on the rods. Truck Shop Quote One ping only Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400593 Share on other sites More sharing options...
41chevy Posted June 15, 2018 Share Posted June 15, 2018 2 hours ago, Truck Shop said: The B/RB blocks and cranks were pretty good but it is a engine that needs a set of Eagle Rods if your going to run one a little hard. At least a set of ARP rod bolts then have the housing bores checked on the rods. Truck Shop That was a stock 1979 440, 150,000 plus miles given a 200 h.p. NOX shot to kill it. 1 Quote "OPERTUNITY IS MISSED BY MOST PEOPLE BECAUSE IT IS DRESSED IN OVERALLS AND LOOKS LIKE WORK" Thomas Edison “Life’s journey is not to arrive at the grave safely, in a well preserved body, but rather to skid in sideways, totally worn out, shouting ‘Holy shit, what a ride!’” P.T.CHESHIRE Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400598 Share on other sites More sharing options...
Truck Shop Posted June 16, 2018 Share Posted June 16, 2018 Ah Ha! Laughing gas. How many shots of NOX had that engine been exposed to before it went poof? Probably several. 😉 Truck Shop Quote One ping only Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400612 Share on other sites More sharing options...
1965 Posted June 16, 2018 Share Posted June 16, 2018 55 minutes ago, Truck Shop said: Ah Ha! Laughing gas. How many shots of NOX had that engine been exposed to before it went poof? Probably several. 😉 Truck Shop Every time it went up against a BOWTYIE! Quote Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400620 Share on other sites More sharing options...
41chevy Posted June 16, 2018 Share Posted June 16, 2018 (edited) 2 hours ago, Truck Shop said: Ah Ha! Laughing gas. How many shots of NOX had that engine been exposed to before it went poof? Probably several. 😉 Truck Shop Only one 12.8 lb full bottle at the point of valve float, burned up two Continental radials and burned two big holes in the asphalt. Edited June 16, 2018 by 41chevy 1 Quote "OPERTUNITY IS MISSED BY MOST PEOPLE BECAUSE IT IS DRESSED IN OVERALLS AND LOOKS LIKE WORK" Thomas Edison “Life’s journey is not to arrive at the grave safely, in a well preserved body, but rather to skid in sideways, totally worn out, shouting ‘Holy shit, what a ride!’” P.T.CHESHIRE Link to comment https://www.bigmacktrucks.com/topic/53487-440-chrysler/page/2/#findComment-400621 Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.