JoeH Posted April 3, 2019 Share Posted April 3, 2019 Enlighten me on the variations of R model hoods. I have a 79 r686st that the back of the fender is a seperate part bonded to the rest of the fender, and a 1981 hood that is all one piece but has a fake seam where the 79 has that bonding. Bought an 88 that probably has an aftermarket hood, and have a 95 with the new style hood. Why the variations on the 79 and 81? Quote Link to comment https://www.bigmacktrucks.com/topic/56527-different-r-hoods/ Share on other sites More sharing options...
JoeH Posted April 3, 2019 Author Share Posted April 3, 2019 I believe the 88 doesn't have any "bump" where the 79 and 81 do. Quote Link to comment https://www.bigmacktrucks.com/topic/56527-different-r-hoods/#findComment-419667 Share on other sites More sharing options...
Lmackattack Posted April 3, 2019 Share Posted April 3, 2019 If I recall right when the mack 300 with front mount intercooling was introduced they added a extra inch or 2 to the hood. this was around 81' early R models had a body line at the back of the fender. this went away some time in the mid 70s? Quote Link to comment https://www.bigmacktrucks.com/topic/56527-different-r-hoods/#findComment-419675 Share on other sites More sharing options...
JoeH Posted April 3, 2019 Author Share Posted April 3, 2019 (edited) You can see the seam I'm talking about in these pictures. The truck is the 79, and the hood on the ground is the 81. The 81 went to the scrap yard years ago, except for hood, engine, trans and rears. Both trucks, 79 and the 81, were/are engine mounted intercoolers, endt676 engines. The 81 was a Canada truck, not sure where it was made. Edited April 3, 2019 by JoeH Quote Link to comment https://www.bigmacktrucks.com/topic/56527-different-r-hoods/#findComment-419678 Share on other sites More sharing options...
Whiskymack Posted April 3, 2019 Share Posted April 3, 2019 This topic came up a few years back but I can't find the thread. I seem to remember someone saying that the hoods were not necessarily made by the same manufacturer so the differences were down to the particular process employed by each manufacturer. Quote Link to comment https://www.bigmacktrucks.com/topic/56527-different-r-hoods/#findComment-419698 Share on other sites More sharing options...
JoeH Posted April 3, 2019 Author Share Posted April 3, 2019 Interesting, because my flatback R cab doesn't have the seam body line at the back of the fender, and it's the oldest truck we have. Quote Link to comment https://www.bigmacktrucks.com/topic/56527-different-r-hoods/#findComment-419746 Share on other sites More sharing options...
Whiskymack Posted April 4, 2019 Share Posted April 4, 2019 All the early flat backed cab R's I have seen had what looks like a one piece hood without the fender seam. I think Mack may have started getting the hoods from a different supplier sometime in the 70's and their manufacture process involved bonding on the fenders so for this reason the seam became a feature. Perhaps because it was quite distinctive it was kept for a while when they switched back to single piece hoods. It would be interesting to know if Mack used more than one supplier at the same time and had both variants available. Later R model hoods didn't have the seam or that slight step in further down the fender either. I suppose Mack just decided to clean up the design a bit. Quote Link to comment https://www.bigmacktrucks.com/topic/56527-different-r-hoods/#findComment-419790 Share on other sites More sharing options...
j hancock Posted April 4, 2019 Share Posted April 4, 2019 Here is some previous conversation on R hoods. https://www.bigmacktrucks.com/topic/46504-r-hood-question/ Quote JimIt doesn't cost anything to pay attention. Link to comment https://www.bigmacktrucks.com/topic/56527-different-r-hoods/#findComment-419791 Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.