Playinghooky13 Posted February 4, 2021 Share Posted February 4, 2021 I've got an 01 ch613 (dump truck now) the D.O.T just shut down the truck today for the low air pressure buzzer was inoperative the light works fine and the buzzer will off and on if you slap the top of the dash. The buzzer is in the instrument cluster and not replaceable mack says. The cluster is about 800 but 5 weeks out here in our area. I'm looking to see if someone can tell me what wires at the back of the cluster I could tie into to install a different buzzer or where the buzzer gets its signal from. Just need to get the truck back in operation the odds of running into the same cop here are very good. I appreciate any help. Quote Link to comment Share on other sites More sharing options...
880joe Posted February 4, 2021 Share Posted February 4, 2021 Can't help you on the wiring up the buzzer but I thought you only had to have 1 form of low air warning device to be legal Quote Link to comment Share on other sites More sharing options...
Playinghooky13 Posted February 4, 2021 Author Share Posted February 4, 2021 That was my thought also. I don't know if it changed or not but just hoping I can fix one up pretty easy. Really dont want to run into the same cop and not have one working I guess. Quote Link to comment Share on other sites More sharing options...
BGarofalo Posted February 4, 2021 Share Posted February 4, 2021 Do you have the new or old style gauge cluster? Quote Link to comment Share on other sites More sharing options...
Playinghooky13 Posted February 4, 2021 Author Share Posted February 4, 2021 If it would help anyone the last 6 of the vin is 140084. I asked mack today when I called about the cluster and they couldn't tell me the wiring or what pressure switch did what they say there system just says pressure switch. Quote Link to comment Share on other sites More sharing options...
Playinghooky13 Posted February 4, 2021 Author Share Posted February 4, 2021 It's the new style cluster Quote Link to comment Share on other sites More sharing options...
880joe Posted February 4, 2021 Share Posted February 4, 2021 I had an 01 vision that had a bad wire connection and buzzer would stay on I never did find where to unhook it finally found my wire issue. Also googled the dot requirement and it said a visable or audible warning device not both Quote Link to comment Share on other sites More sharing options...
Joey Mack Posted February 4, 2021 Share Posted February 4, 2021 (edited) OK....I've been here before.... What I did was go to the pressure switch behind the pedals. "T" in a 1/8" NPT "T" buy a low air pressure switch and install it in the "T".. its the same switch that turns the brake lights off when air pressure is up. i put the extra switch in in the case the original goes bad, I don't lose 2 functions... you can buy a buzzer for a late 90's CH ( it's a green square thing) It has a positive and negative post. so you just need to figure that out, and wire it into the switch and zip tie it above the pedals some where... you can also put a 10amp fuse in a holder in-line if you feel the need to protect it. it will buzz until pressure reaches about 85 PSI... it takes about an hour to do this, you can "mock" the whole thing on the work bench and then install it into the "T" fitting. I think those buzzers are less than $30.00 so for around $50 bucks you will have a buzzer, thats replaceable.... Jojo P.S. 880joe is right about one or the other low air warnng.. dont know what The D.O.T. officer was thinking, .. Edited February 4, 2021 by Joey Mack More content needed 1 Quote Link to comment Share on other sites More sharing options...
MACKX Posted February 4, 2021 Share Posted February 4, 2021 Good call Jojo...... I have also done the same thing before to make the buzzer operational after the cluster takes a dump...always seems to be the air alarm but everything else works fine 😒..... just when I looked up the buzzer I used an RB690S vin lol that’s horrible the DOT officer is a dick and will probably hassle you if you don’t make the buzzer operational again...... Quote Link to comment Share on other sites More sharing options...
Playinghooky13 Posted February 4, 2021 Author Share Posted February 4, 2021 Yes I have a feeling the officer will be on the lookout for the truck and it probably would not go in our favor. I will be doing what Joey mack has done. Thanks for all the input. 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.