cruiseliner64 Posted August 21 Author Share Posted August 21 7 hours ago, mechohaulic said: nope figured wrong (again). not same . wondered about the mentioning of gear box. worn marks on shift rails definitely indicates source of oil leakage. F model shift lever stayed on the tower also . was a simpler design. brain cells now attempting to remember which cab over had the shift lever attached to cab which connected lever to linkage when cab lowered by a ball and socket arrangement ??? think it was the small MB?? It is the Cruiseliner.when cab is tilted the gearlever lifts with the cab and the ball stays on the shift tower.when lowering the cab you have to check the ball lines up to the socket in the bottom of the gearlever.....we have found the brass bushs that the rods pass through on line.....but the rest may havevto be made up. Paul 1 Quote Link to comment https://www.bigmacktrucks.com/topic/74475-first-drive-in-the-cruiseliner/page/2/#findComment-557391 Share on other sites More sharing options...
Vladislav Posted August 21 Share Posted August 21 The shift linkages of MH and Criseliner have about nothing in common. Excepting both have the lever separated from the tower when the cab is up and both use a U-joint. The matter of difficulties with shifting may be due to worn out linkage (you aren't able to find the spot where you shift into a certain gear) or due to worn out sliding clutches/mating teeth in the tranny gear wheels. This second way you have grinding in the gear change moments. Shifing Mack trannies require special skill which could be obtained by practice. I tell this as a guy who has never had experience driving American truck or another non-synchro transmission before appeared by the wheel of my 1st Mack truck. Now I understand that transmission had hard wear on the noted above parts but anyway could be shifted smooth if you know particular moments to get into a particular gear. 2 Quote Никогда не бывает слишком много грузовиков! leversole 11.2012 Link to comment https://www.bigmacktrucks.com/topic/74475-first-drive-in-the-cruiseliner/page/2/#findComment-557404 Share on other sites More sharing options...
kscarbel2 Posted August 22 Share Posted August 22 On 8/21/2024 at 5:05 AM, cruiseliner64 said: It is the Cruiseliner.when cab is tilted the gearlever lifts with the cab and the ball stays on the shift tower.when lowering the cab you have to check the ball lines up to the socket in the bottom of the gearlever.....we have found the brass bushs that the rods pass through on line.....but the rest may havevto be made up. Paul The applicable seals and bushings were used in many other Mack applications, hence they are still available. 2 Quote Link to comment https://www.bigmacktrucks.com/topic/74475-first-drive-in-the-cruiseliner/page/2/#findComment-557417 Share on other sites More sharing options...
cruiseliner64 Posted August 22 Author Share Posted August 22 Thanks for that.we will keep looking.im enjoying this project.just trying to get the old gal right.... 1 Quote Link to comment https://www.bigmacktrucks.com/topic/74475-first-drive-in-the-cruiseliner/page/2/#findComment-557428 Share on other sites More sharing options...
ws721 Posted August 23 Share Posted August 23 On 8/17/2024 at 5:03 PM, BOBWhite said: A guy on here rebuilt the shift tower on an Mh awhile back, not sure if there would be any similarities. Do Cruiseliners have a shift tower like an Mh or do they have the older style that goes in between the seat to the floor? Completley different set up in a Cruiseliner Quote Remember if it's got a hood it's no good! Link to comment https://www.bigmacktrucks.com/topic/74475-first-drive-in-the-cruiseliner/page/2/#findComment-557487 Share on other sites More sharing options...
ws721 Posted August 23 Share Posted August 23 As mentioned earlier by others, check the U joints, thats the simpliest task. Then go into the box on shift tower. Chances are its worn in there. They get worn and then sloppy. I did tach weld the gear to the shaft as the the keyway would not stay tight. That is a last resort though. I've owned and run F models, Cruiseliners and MH's, they all had there good and bad points. I think the Cruiseliner shift linkage, when in good order, has the best feel to it when shifting. Just my opinion 2 Quote Remember if it's got a hood it's no good! Link to comment https://www.bigmacktrucks.com/topic/74475-first-drive-in-the-cruiseliner/page/2/#findComment-557489 Share on other sites More sharing options...
Popular Post cruiseliner64 Posted October 29 Author Popular Post Share Posted October 29 On 8/23/2024 at 1:12 PM, ws721 said: As mentioned earlier by others, check the U joints, thats the simpliest task. Then go into the box on shift tower. Chances are its worn in there. They get worn and then sloppy. I did tach weld the gear to the shaft as the the keyway would not stay tight. That is a last resort though. I've owned and run F models, Cruiseliners and MH's, they all had there good and bad points. I think the Cruiseliner shift linkage, when in good order, has the best feel to it when shifting. Just my opinion Hi all,we have changed the UJs on the shift linkage and bushes but so far we are unable to get the oil seals.in order to provide some lub we packed it with a light grease as this doesnt seep out.its a major improvement in gear shifting.we took the truck for a long drive today and it a joy to drive.the only problems we have left to sort out is a slight weep from the bottom corner of the rad and new tyres.my son and I cant thank you all enough for all the advise and encourgement you all gave us since we got our truck.this is a great site to be a member of. 4 Quote Link to comment https://www.bigmacktrucks.com/topic/74475-first-drive-in-the-cruiseliner/page/2/#findComment-560985 Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.